Wilton Parts

Fix Number

FIX10463886

Manufacturer Part Number

BB-6202ZZ

This is an authentic OEM replacement part for certain models of Jet, Powermatic, and Wilton tools that is sourced from the manufacturer. To ensure that this will fit your tool, please see the "Model Cross Reference List" below. This part has an outer diameter of 1.5", and metal shielding on both sides. The bearing is used to reduce friction between two rotating parts. It keeps wear on the equipment to a minimum, and helps the mechanics run efficiently. Depending on how often you use your tool, your bearings will need routine replacement due to continual pressure on them. Signs of broken or failing Ball Bearings include squealing, screeching, or grinding noise when powering the device off. Each is sold individually.

Fix Number

FIX10514778

Manufacturer Part Number

21500-06

When a swivel-base vise turns after being locked, the lock nut assembly may be worn or damaged. The nut and bolt work with the base to hold the vise at the chosen position. A working assembly also allows the base to be loosened when the vise must face a new direction. Check the threads, handle, locking pads, and base for damage before choosing the repair. Keep fingers clear while moving the vise, and only use hand pressure when tightening the lock handle. Do not strike it or add an extension bar.

Fix Number

FIX10515145

Manufacturer Part Number

5508441

This part is made of metal and is sold individually. The drive shaft attaches to the bearing housing. A screwdriver may be helpful when replacing this part. It will require replacing if it becomes broken. This is a genuine item that is supplied by the original equipment manufacturer for use with Wilton and Jet sanders.

Fix Number

FIX10463888

Manufacturer Part Number

BB-6203ZZ

This ball bearing is 17 mm and fits a variety of gardening power tools. The ball bearing has two contact rubber seals on each side and two non-contact metal shields on each end as well. Tip: if your tools needs only one seal or shield, then take off one of the shields or seals from this ball bearing. Refer to the manual provided by the manufacturer for further installation instructions and a detailed diagram.

★★★★★

★★★★★

7 Reviews

Fix Number

FIX10514501

Manufacturer Part Number

11104S51

This screw and handle assembly is an authentic Craftsman replacement part, and is compatible with bench vises. This part lets you loosen or fasten the vise jaws. This assembly includes the screw and the handle that is pre-assembled. This part is made of metal and sold individually.

Fix Number

FIX10516120

Manufacturer Part Number

5640371

This item is sourced directly from the original equipment manufacturer. It is specially designed for use with Jet and Wilton sanders. The idler pulley helps to apply tension on the belt. Over time it may wear out or get damaged eventually requiring a replacement. It is made of high-quality material and is sold individually. Check the diagrams of your model for the exact location and the correct installation of this part. You will need a wrench set to remove and secure the hardware that holds the idler.

Fix Number

FIX10378028

Manufacturer Part Number

2904200

This is an original part from the Jet manufacturer. The lower (pipe) jaws are constructed of carbon steel, and has been made for use with many vise tools. This item includes two screws, and has curved edges which have been designed to secure pipes and other similar sized materials. This component is sold individually. A screwdriver is necessary in the removal and replacement.

Fix Number

FIX10463892

Manufacturer Part Number

BB-6204ZZ

This is an authentic OEM replacement part used for various handheld power tools including models by Powermatic, Jet, and Wilton. Bearings stabilize and buffer moving parts to facilitate rotation of such parts as shafts, axles, and gears. They are commonly replaced due to this high wear function. This part sold individually.

Fix Number

FIX10378027

Manufacturer Part Number

2904110

This is a genuine replacement part which is sourced directly from the original manufacturer for use with Jet and Wilton vises. The jaw is an important component which helps to provide a tight grip. It provides an identical replacement for a missing or a damaged part that was installed on a new unit. You may require a screwdriver or wrench when replacing this item. Two durable metal vise jaws and the hardware to secure them are included. Refer to the owner's manual of your model for the correct application. A screwdriver will be needed to perform the repair.

Fix Number

FIX10516515

Manufacturer Part Number

5783471

This item is a genuine part that has been sourced from the original manufacturer to be used with verticle bandsaws from Wilton and Jet. The durable plastic insert fits into the cap in the table where the blade passes through the table. The insert is used to reduce the gap around the blade in order to better support the material as it is being cut. Inserts wear down from normal use, and will eventually need to be replaced to maintain clean accurate cuts. This part is priced as a single item, please note tools may not be necessary to install the insert.