Bolens Trimmer Parts
Start With Your Model Number
Find Parts Fast Guaranteed Fit Repair VideosNeed help finding your model number?
Popular Bolens Trimmer Parts
Bump Head Knob Assembly
Fix Number FIX9306452
Manufacturer Part Number 791-153066BThis bump knob assembly fits lawn and gardening tools, usually trimmers. This part bumps on the ground to advance the cutting line from the spool. With time and use, this part can wear out easily. It is recommended to order an extra knob assembly to always have on hand. Refer to the manual provided by the manufacturer for installation instructions and safety practices.
Primer and Hose Assembly
Fix Number FIX10014772
Manufacturer Part Number 791-683974BThis is a primer and hose assembly, and it is used on various lawn equipment. The assembly comes with two parts. The first is the hose which is almost 5 inches long, and less than a 1/4 inch thick. The second part is the primer bulb or primer pump, and that is 2 inches long, and 1 inch wide, with a round bulb head. Together, the primer and hose assembly fill the carburetor with fuel to give your machine a quicker start. After time, your hose will crack and your primer will lose elasticity. Both will have to be replaced when this happens. Before starting this repair make sure to drain the fuel from the tank, and remove the spark plug.
Fuel Line and Filter
Fix Number FIX10014709
Manufacturer Part Number 791-682039This fuel line filters the fuel in the tank as it pushes into the carburetor by the primer bulb. If your carburetor is not getting fuel, ports get clogged, or the fuel line is leaking, then replacing this part will solve these problems. It is important to replace it as soon as damage is noticed because clogging can result in your engine not starting. For this repair, you will need the following tools: torx/Phillips drivers, long screwdriver, long-nosed pliers, long screwdriver, cutters or scissors, and two-cycle engine oil. For this repair, first remove the retainer ring from the fuel line and insert it through gas cap opening. Next, thread the fuel line through the hole in the bottom of the fuel tank and pull the line through to firmly place it against the tank wall. For the last steps, put the retainer ring on the fuel line and press the ring firmly against the external side of the fuel tank wall. Lastly, attach it to correct line on the carburetor.
Fuel Return Line
Fix Number FIX9137685
Manufacturer Part Number 791-181086This is a fuel return line, and it is used with various outdoor lawn equipment. Fuel travels through the return line into the carburetor, and from the primer bulb/pump into the fuel system. The line returns the extra fuel back into the tank. This part will crack and become brittle over time. If your fuel line is leaking, you will need to replace it. Before you begin repair work on your equipment make sure you drain the fuel from the tank, and remove the spark plug.
Line Trimmer Spool
Fix Number FIX9119496
Manufacturer Part Number 753-1155This spool is for line trimmers. Spool houses the cutting line and fits inside the cutting head to cut grass and weeds. Wear work gloves to protect your hands when installing this part.
Fix Number FIX10014644
Manufacturer Part Number 791-610317B
Fuel Tank Assembly
Fix Number FIX10009586
Manufacturer Part Number 753-06183This is an authentically sourced fuel tank assembly, including the fuel lines, fuel cap, fuel filter, and screws needed for assembly. This fuel tank assembly is for trimmers, and is where the fuel is filtered and stored for use with the engine. Due to its constant contact with fuel, especially if fuel has been left it in for extended periods of time, it may crack, in which case it should be replaced immediately. Leaking gas is very dangerous, so it is important that it get fixed quickly. Before beginning this repair, drain the gas from the tank before installing the new one.
Fix Number FIX10014381
Manufacturer Part Number 791-182405This switch is used on a variety of trimmers, blowers and other similar gardening equipment. This switch controls the on and off operations of your tool. Switches have mechanical internals, which degrade and wear out in time. In this case, switches are a commonly replaced part. *Please note: this part is sold individually. The tool needed for this repair is a screwdriver. To repair, first remove screws that hold the pieces of housing together. Next, disconnect wires from the old switch as well as the wires from the housing. Now you can install the new switch in the housing and connect the correct wires to it. For further installation instructions, refer to the diagram provided by the manufacturer.
Fix Number FIX9119300
Manufacturer Part Number 753-06190It is an authentic manufacturer-sourced replacement part that i supplied for Craftsman trimmers. The function of a carburetor is to mix the air and the gas into a highly combustible mix before it goes into the engine, over time components may wear out eventually requiring a replacement to ensure peak performance. It is a high-quality metal body carburetor with included rubber primer bulb, please note this assembly is sold individually. When replacing a carburetor it is advised to replace the gaskets as well to ensure the proper seal, keep in mind gaskets are sold separately.
Fix Number FIX11839169
Manufacturer Part Number 753-04119This is a genuine OEM replacement throttle trigger (red). The throttle trigger is responsible for managing the speed of the engine. The throttle cable attaches to the trigger, which connects to the throttle lever on the carburetor. It is in constant use, so it tends to deteriorate over time, making it a common replacement part.