Black and Decker Timmer Parts

Black and Decker Appliance Parts
Shop By Appliance Type

Popular Black and Decker Timmer Parts

$3.65
In Stock
COVER
★★★★★
★★★★★
(2)
Fix Number FIX12443187
Manufacturer Part Number 385022-03N
This is an OEM replacement cover for a string trimmer or edger. The cover holds the spool and line securely inside the spool housing. If this part has cracked or damaged, it will need to be replaced. When removing this part, make sure the trimmer is unplugged, release the tabs by pressing them down with your fingers, and pull it straight off. Place the new cover on by simply snapping it into place. This plastic cover is sold individually.
$10.16
In Stock
Bump Cap
★★★★★
★★★★★
(1)
Fix Number FIX10184171
Manufacturer Part Number 682378-02
2-5/8-Inch Wide This is a genuine Black and Decker replacement part. It is sold individually.. Its purpose is to hold the spool and bumper in the spool housing. It has 2 tabs that snap into the spool housing. To remove this part press on the 2 tabs and it will release from the spool housing.
$2.99
In Stock
Lever Assembly
Fix Number FIX12004487
Manufacturer Part Number 90567077
This authentic string trimmer lever assembly is sold individually. The lever is what controls the amount of line that is fed from the auto-feed spool. The lever tends to wear over time, and so should be inspected regularly. If the automatic line feed is not working, a malfunctioning lever is likely the cause. Remove the spool and check if the lever in the spool housing can move freely, if not, adjust or replace if damaged.
Fixes these symptoms
$2.99
In Stock
Spring
Fix Number FIX10254180
Manufacturer Part Number 90566944
This is an OEM spring located between the spool and spool cover of your trimmer. It is designed to hold the spool in position. This spring can lose tension over time and may cause the trimmer head to feed too much line or not feed any line at all, indicating the need for a new spring. The spring applies pressure to the spool, pulling it firmly next to the top of the trimmer head and lever. The lever is what regulates the amount of line coming out of the spool. This repair could not be any easier, simply remove the trimmer head cap by pushing down on the two tabs on either side. This will expose the spring, which you will see positioned onto a tab on the cap, and can just be pulled off, and a new one can be installed in its place.
$2.99
In Stock
Spring
Fix Number FIX10184168
Manufacturer Part Number 682235-00
$13.35
In Stock
Spool
Fix Number FIX10165961
Manufacturer Part Number 143684-01
This part includes one OEM spool replacement for a trimmer. This spool includes 20-feet of factory-wound 0.65-inch line. The spool houses the cutting line and is located inside the cutting head to cut grass and weeds. The spool can wear over time from being repeatedly tapped against the ground. You might also replace it to avoid having to wrap a new trimmer line when it runs out. For this quick and easy DIY repair, start by removing the bump cap from the trimmer head, which is secured with two plastic locking tabs. Depress the tabs and remove the cap from the hub. Now it should be easy to just remove the spool. Then take the trimmer line and pull out a few inches and lock it into the tab on the spool to hold it in place. Next, thread the trimmer line through the eyelet, align the spool with the shaft, and tug on the trimmer line to free it from the holder. To finalize the repair, reinstall the bump cap.
$6.32
In Stock
Switch,On/Off
★★★★★
★★★★★
(2)
Fix Number FIX10170531
Manufacturer Part Number 383994-00
Installation Instructions
Craig from FREMONT, CA
Always on equal a safety issue.
The switch has a spring tension so that the default condition is in the off position. The trigger moves the switch to the on position when the user grips the trigger mechanism and provides an active resistance to the spring portion of the switch, enabling power to the hedge trimmer motor. There are six to seven torx T15 screws that, when removed, enables the unit to separate into equal parts, exposing the internal trigger mechanism and the switch. The replacement drops right in after removing the old switch. Re connect the electrical connectors to the new switch. Re align the the two halves and tighten the torx screws. The hedge trimmer is then good to go! Read more...
$12.07
In Stock
Line Trimmer Spool Assembly
Fix Number FIX12004280
Manufacturer Part Number 90540850
This spool assembly is for line trimmers. The spool assembly includes the spool and line. It fits inside the cutting head to cut grass and weeds. Wear work gloves to protect your hands when installing this part.
$2.99
In Stock
Blade
Fix Number FIX10167402
Manufacturer Part Number 243805-00
$17.93
In Stock
Charger
Fix Number FIX12004687
Manufacturer Part Number 90592363-01
This is an OEM 18v NiCad battery charger used in various model types, such as drills, chainsaws, hedge trimmers, etc. This part includes the charger only. When the battery is placed in the charger, a red-light indicator will come on, telling you there is a connection between the battery and charger. This light remains on while it is connected to a power source. It will not turn off, flash, or change color once the charge is complete.

Appliance Type

Popular Black and Decker Timmer Models