Weed Eater Lawn Tractor Hardware

Fix Number

FIX9982804

Manufacturer Part Number

584953901

This OEM hex head bolt is for lawn tractors. It is used on mower deck mandrels for mounting the spindles to the deck. This is a self-threading screw and will need to be replaced if it is worn or missing altogether. It is sold individually and is made of metal. You will need a wrench to remove the old screw and tighten the new one.

Fix Number

FIX9143890

Manufacturer Part Number

812000029

This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part of a mower wheel or steering assembly). When it is installed, the part that is visible acts as a shoulder, holding the specific component or assembly together. This very small metal ring clip (approximately 1-inch by 1-inch) is sold individually.

Fix Number

FIX9286886

Manufacturer Part Number

532187690

This is an OEM lawn mower deck mandrel spacer washer, sold individually. It measures approximately 43/64-Inches in diameter, 1-1/8-Inches outer diameter, and 5/32-Inches thick (these measurements are approximate). In general, washers help to spread load, can provide insulation such as electrical, and can also help to prevent galvanic corrosion.

Fix Number

FIX9020856

Manufacturer Part Number

532193003

This is an OEM bolt and washer assembly, designed to hold the lawnmower blade to the spindle shaft. This threaded bolt has a curved rounded head and measures approximately 7/16-inches by 2-inches. If your lawnmower blade is not rotating properly or making grinding sounds, these are usually the first signs that that the bolt and washer may be worn. For this beginner repair, start by making sure the engine is cool, the spark plug is removed, and the mower is on its side. Remove the old bolt and washer with a socket. Insert the new bolt and washer into the blade opening and secure it with the socket.

Fix Number

FIX9008998

Manufacturer Part Number

532121749

This is a flat metal washer found in various models of lawn mowers and is sold individually. This flat washer can have various functions depending on the equipment; however, its general purpose is to spread the load under a bolt or screw. It also helps to reduce heat and friction as the fastener is tightened. This repair may require a screwdriver or socket wrench, depending on the fastener for your model. This is a single flat washer; the fasteners are sold separately.

Fix Number

FIX9015920

Manufacturer Part Number

532188967

This is a Genuine Manufacturer Approved replacement washer used on lawn and garden equipment. This part is made out of Metal and is Sold Individually. Washer helps to distribute the pressure evenly over the surface and provides a solid grip.

Fix Number

FIX9022497

Manufacturer Part Number

532409149

This is a genuine hex flange locknut for a lawn mower. It attaches to the carriage bolt (sold separately), fastening the axle assembly braces in place. This part is sold individually, however most models require three. For this repair you will need a wrench set.

Fix Number

FIX9285696

Manufacturer Part Number

532110452

This is a genuine Craftsman replacement part for use in lawn tractors. It helps to connect the deflector rod to the deflector shield. The metal push nut is a small part and will need to be replaced if it becomes lost or broken. A screwdriver and a set of pliers may be needed to replace this part. This item is sold individually.

Fix Number

FIX16381821

Manufacturer Part Number

596134801

This high-quality item is an authentic OEM hardware that is designed for use with Craftsman riding lawn mowers and garden tractors. It is one of the locknuts that is utilized to secure the pulleys. A locknut is a nut that resists loosening under vibration and torque. Refer to the diagrams of your model for the exact location and the correct application of this part. One durable metal locknut is included. You will need a wrench to secure and remove it.

Fix Number

FIX9016072

Manufacturer Part Number

532194208

This is a 5/16-inch metal cotter pin and it is sold as an individual part. Cotter pins secure a variety of different assemblies by placing them through a drilled hole in a shaft or bolt, such as on a wheel on a lawn tractor. If your cotter pin is missing or damaged this authentic OEM part is designed to replace the original.