Weed Eater Lawn Mower Parts

Start With Your Model Number

Need help finding your model number?
Find Parts Fast
Guaranteed Fit
Repair Videos
Fix.com search
Weed Eater Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular Weed Eater Lawn Mower Parts

Lawn Tractor Mandrel Assembly – Part Number: 587819701
Lawn Tractor Mandrel Assembly
$48.56
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX12087499
Manufacturer Part Number
587819701

Installation Instructions

Terrence from LORENA, TX
Blade mandrel replacement
1. Remove mower deck.
2. Remove mower blade from defective mandrel.
3. Clean caked up grass from underside of mower deck.
4. Remove belt pulley from top of defective mandrel.
5. Remove four bolts fastening defective mandrel to deck. Note: bolts will most likely shear - make sure you have new ones.
6. Install new mandrel to deck using four new self-tapping bolts.
7. Reinstall mower blade to new mandrel assembly.
8. Reinstall belt pulley to new mandrel assembly.
9. Reinstall mower deck to tractor. Read more...
Ring Klip Number T5304-75 – Part Number: 812000029
Ring Klip Number T5304-75
$3.99
In Stock
Fix Number
FIX9143890
Manufacturer Part Number
812000029
This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part of a mower wheel or steering assembly). When it is installed, the part that is visible acts as a shoulder, holding the specific component or assembly together. This very small metal ring clip (approximately 1-inch by 1-inch) is sold individually.
Bolt and Washer Assembly – Part Number: 532193003
Bolt and Washer Assembly
$8.71
In Stock
Fix Number
FIX9020856
Manufacturer Part Number
532193003
This manufacturer-approved bolt and washer assembly is for lawn tractors. Wear work gloves to protect your hands when installing this part.
Washer 25/32 x 1-1/4 x 16 Ga. – Part Number: 532121749
Washer 25/32 x 1-1/4 x 16 Ga.
$3.99
In Stock
Fix Number
FIX9008998
Manufacturer Part Number
532121749
This is a flat metal washer found in various models of lawn mowers and is sold individually. This flat washer can have various functions depending on the equipment; however, its general purpose is to spread the load under a bolt or screw. It also helps to reduce heat and friction as the fastener is tightened. This repair may require a screwdriver or socket wrench, depending on the fastener for your model. This is a single flat washer; the fasteners are sold separately.
Nut, Hex, Flangelock – Part Number: 532409149
Nut, Hex, Flangelock
$4.99
In Stock
Fix Number
FIX9022497
Manufacturer Part Number
532409149
This is a genuine hex flange locknut for a lawn mower. It attaches to the carriage bolt (sold separately), fastening the axle assembly braces in place. This part is sold individually, however most models require three. For this repair you will need a wrench set.
Washer Hardened – Part Number: 532188967
Washer Hardened
$4.99
In Stock
Fix Number
FIX9015920
Manufacturer Part Number
532188967
Solenoid – Part Number: 582042802
Solenoid
$13.69
In Stock
Fix Number
FIX16372182
Manufacturer Part Number
582042802
Washer-Spacer – Part Number: 532187690
Washer-Spacer
$3.99
In Stock
Fix Number
FIX9286886
Manufacturer Part Number
532187690
This is an OEM lawn mower deck mandrel spacer washer, sold individually. It measures approximately 43/64-Inches in diameter, 1-1/8-Inches outer diameter, and 5/32-Inches thick (these measurements are approximate). In general, washers help to spread load, can provide insulation such as electrical, and can also help to prevent galvanic corrosion.
Switch-Ign – Part Number: 532193350
Switch-Ign
$14.93
In Stock
Fix Number
FIX9020864
Manufacturer Part Number
532193350
This ignition switch has been sourced directly from the original manufacturer and is sold individually (key sold separately). The ignition switch is also sometimes referred to as a starter switch and is enclosed in a plastic housing. A common sign that this part is malfunctioning is if the electric starter is not engaging. For this quick and easy repair, start by making sure the switch is in the off position and the key has been removed. Lift the hood up, locate the steering housing and press the tabs to disengage the old switch. Disconnect the wires and install your new OEM ignition switch.
Fixes these symptoms

Installation Instructions

MICHELE h from ARGYLE, NY
Barely turns over to start, dead battery
Disconnected battery, unplugged key switch, using screwdriver removed old switch and replaced with new switch. Removed battery cables from old solenoid and replaced with the new one. End results still doesn't turn over enough to start it. Failed repairs Read more...
Pin Cotter 5/16 Bow Tie Lock – Part Number: 532194208
Pin Cotter 5/16 Bow Tie Lock
$3.99
In Stock
Fix Number
FIX9016072
Manufacturer Part Number
532194208
This is a 5/16-inch metal cotter pin and it is sold as an individual part. Cotter pins secure a variety of different assemblies by placing them through a drilled hole in a shaft or bolt, such as on a wheel on a lawn tractor. If your cotter pin is missing or damaged this authentic OEM part is designed to replace the original.

Weed Eater Lawn Mower Appliance Types

Related Weed Eater Lawn Mower Parts

Popular Weed Eater Lawn Mower Models

View More
+