Weed Eater Parts

Weed Eater Appliance Parts

Popular Weed Eater Parts

Solenoid
$34.27
In Stock
Fix Number
FIX16372182
Manufacturer Part Number
582042802
It is a genuine OEM sourced part is specially designed for riding lawn mowers and garden tractors. The solenoid acts like an electromagnetic switch, it engages and routes the battery electrical supply to the engine starter when the ignition switch is rotated to the start position. Unfortunately, over time it may wear out or get damaged eventually requiring a replacement. Keep in mind this high-quality solenoid is sold individually. You will need a screwdriver and a wrench set to perform this repair. Check the diagrams of your model for the exact location and the correct installation of the new part.
Lawn Mower Mandrel Spacer Washer
$7.52
In Stock
Fix Number
FIX9286886
Manufacturer Part Number
532187690
This is an OEM lawn mower deck mandrel spacer washer, sold individually. It measures approximately 43/64-Inches in diameter, 1-1/8-Inches outer diameter, and 5/32-Inches thick (these measurements are approximate). In general, washers help to spread load, can provide insulation such as electrical, and can also help to prevent galvanic corrosion.
Lawn Mower Ring Clip
$6.55
In Stock
Fix Number
FIX9143890
Manufacturer Part Number
812000029
This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part of a mower wheel or steering assembly). When it is installed, the part that is visible acts as a shoulder, holding the specific component or assembly together. This very small metal ring clip (approximately 1-inch by 1-inch) is sold individually.
★★★★★
★★★★★
2 Reviews
Fix Number
FIX9285148
Manufacturer Part Number
530095646
This is a single fuel filter found in numerous types of lawn and garden equipment that have small engines. The fuel filter cleans the fuel before making its way to the carburetor, thus preventing build up. If this flow of fuel is blocked, this will cause issues with starting the engine. Luckily, this common maintenance task is very quick and easy to do, and should be done annually, if not more depending on usage. You will start by draining the fuel tank and removing the spark plug.
Fixes these symptoms
  • Engine stops after a few seconds or minutes
  • Will Not Start
  • See more...

Installation Instructions

Larry from Sanford, NC
fuel line is very tight going on
Using forceps, hold tight grip on fuel line about only 1/8 of an inch back of end and lube lightly. Push slowly and work onto nipple. Read more...
Lawn Mower Washer
$6.55
In Stock
Fix Number
FIX9008998
Manufacturer Part Number
532121749
This is a flat metal washer found in various models of lawn mowers and is sold individually. This flat washer can have various functions depending on the equipment; however, its general purpose is to spread the load under a bolt or screw. It also helps to reduce heat and friction as the fastener is tightened. This repair may require a screwdriver or socket wrench, depending on the fastener for your model. This is a single flat washer; the fasteners are sold separately.
Lawn Mower Flange Wheel Bearing
$12.05
In Stock
Fix Number
FIX9006914
Manufacturer Part Number
532009040
This is a premium-quality OEM front wheel flange bearing (sometimes called bushing) commonly used in riding lawn mowers. They are used to keep the wheel held in place securely. It is sold individually but two are needed for each front wheel. It is recommended that they be replaced at the same time. Install this part with the flat side facing the grease zerk in the rear side of the wheel.
Lawn Mower Hardened Washer
$6.55
In Stock
Fix Number
FIX9015920
Manufacturer Part Number
532188967
This is a Genuine Manufacturer Approved replacement washer used on lawn and garden equipment. This part is made out of Metal and is Sold Individually. Washer helps to distribute the pressure evenly over the surface and provides a solid grip.
Bolt and Washer Assembly
$12.05
In Stock
Fix Number
FIX9020856
Manufacturer Part Number
532193003
This is an OEM bolt and washer assembly, designed to hold the lawnmower blade to the spindle shaft. This threaded bolt has a curved rounded head and measures approximately 7/16-inches by 2-inches. If your lawnmower blade is not rotating properly or making grinding sounds, these are usually the first signs that that the bolt and washer may be worn. For this beginner repair, start by making sure the engine is cool, the spark plug is removed, and the mower is on its side. Remove the old bolt and washer with a socket. Insert the new bolt and washer into the blade opening and secure it with the socket.
Cap Axle Black 1 50 x 1 00
$6.55
In Stock
Fix Number
FIX9007667
Manufacturer Part Number
532104757
This is an OEM axle cap for lawn tractors and is sold individually. It stops debris from getting into the wheel hub and axle. This axle cap is prone to wear and tear and should be replaced when it is goes missing or appears damaged. No tools are necessary for this easy repair, simply locate the cap axle on the rim of the wheel and remove.
Lawn Tractor Mandrel Assembly
$73.55
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX12087499
Manufacturer Part Number
587819701

Installation Instructions

Terrence from LORENA, TX
Blade mandrel replacement
1. Remove mower deck.
2. Remove mower blade from defective mandrel.
3. Clean caked up grass from underside of mower deck.
4. Remove belt pulley from top of defective mandrel.
5. Remove four bolts fastening defective mandrel to deck. Note: bolts will most likely shear - make sure you have new ones.
6. Install new mandrel to deck using four new self-tapping bolts.
7. Reinstall mower blade to new mandrel assembly.
8. Reinstall belt pulley to new mandrel assembly.
9. Reinstall mower deck to tractor.
Read more...

Weed Eater Appliance Types