Murray Lawn Mower Belts

Fix Number

FIX9011522

Manufacturer Part Number

532144959

This is a drive belt for a lawn tractor or lawn mower. The belt is designed to turn the pulley that spins the blades on the mower deck. If the blade is not turning correctly, it could be due to a worn belt. This OEM rubber drive belt measures approximately 95-Inches long and 1/2-Inch wide, however keep in mind that a used belt may measure differently due to stretching. For this repair you will need a wrench set.

Fix Number

FIX17016481

Manufacturer Part Number

531165901

This genuine OEM belt guard is designed for use with lawn tractors and riding mowers manufactured by Husqvarna, Ryobi, Poulan, Weed Eater, and Jonsered. Positioned between the washer and the arm idler, it helps guide the belt and maintain proper alignment during operation. Made of durable metal, this part should be replaced if it becomes damaged or broken. It is sold individually, and tools such as a set of pliers, a socket set, and a wrench set may be needed for installation. For accurate placement, refer to your model’s diagram.

Fix Number

FIX9072068

Manufacturer Part Number

7022252YP

Spindle belt. Width: 1/2 " Length: 73 1/2 "

Fix Number

FIX11831567

Manufacturer Part Number

37X88MA

Genuine Murray replacement part, this item is sold individually. This is the Mower Drive Belt for the Lawn Tractors listed below. It is routed on three pulleys. Two of which drive the shafts which the mower blades connect to.

Fix Number

FIX11831566

Manufacturer Part Number

37X87MA

Genuine Murray replacement part, this item is sold individually. This is the belt that transmits power from the engine to the transmission giving the Tractor motion. It is put on the large pulley that is connected to the transmission, then on the top of the Stacked Pulley Assembly. It is used on all of the Lawn Tractor models shown below.

Fix Number

FIX11831556

Manufacturer Part Number

37X65MA

This is an OEM Murray part directly sourced from the manufacturer for lawn tractors. It wraps around the drive pulley and the stack pulley assembly and helps to rotate both parts. Pliers may be needed to replace this part if it becomes broken or stretched. This 30" belt is priced individually.

Fix Number

FIX9014158

Manufacturer Part Number

532175436

This is a genuine replacement part sourced from the original manufacturer for use with walk-behind lawnmowers. The special v-belt is commonly used to link the motor pulley and the transmission's drive pulley. This v-belt is available as an individual replacement part, please see model diagram for associative parts.

Fix Number

FIX16298804

Manufacturer Part Number

1728008SM

This is a genuine manufacturer-sourced replacement v-belt which is specially designed for use on Murray, Snapper and Simplicity lawn and garden equipment. It is the main belt which drives the unit, over time it may wear out or stretch eventually requiring a replacement. Clean pulleys before installing the new belt to ensure top performance and longevity with your new belt. This high-quality part is made of durable rubber material and it is sold individually.

Fix Number

FIX8892237

Manufacturer Part Number

1732955SM

This is an authentic manufacturer sourced replacement v-belt which is specially designed for use with Murray, Snapper, and Simplicity lawn mowers. It is the main deck belt that is used to drive the blades, unfortunately, over time belts tend to wear out and stretch eventually requiring a replacement to maintain peak performance. Clean the pulleys before installing the new belt to ensure top performance and longevity with your new belt. Keep in mind this high-quality part is made of durable rubber and is sold individually.

Fix Number

FIX12089861

Manufacturer Part Number

37X66MA

This is a Genuine Manufacturer Approved replacement Belt used on Murray Lawn Tractors. This part is made out of Rubber and it is Sold Individually. This is the the Smaller Belt that drives Blades on your unit. Clean pulleys before installing the new belt to ensure top performance and longevity with your new belt. Inspect belt periodically and replace it when worn or stretched to maintain peak performance. You would need a Wrench set and Pliers to replace this belt. • For your safety make sure to disconnect the spark plug wire. • Fist you would need to lower the mower deck to the lowest position • Then move the blade engagement lever to the Off position. • Roll the belt off the engine pulley from between the belt guide and pulley. • Remove mower deck by removing the bow-tie pins securing the left and right lift arms • Disconnect the blade engagement cable from the mower deck • Remove the bolts from the mower deck belt pulley covers and pull the covers off. • Loosen but don't remove the nuts on the top of the idler pulleys. • Install the new mower deck belt through the belt guides and around the pulleys. • Tighten the nuts on the top of the idler pulleys. • Re-Assemble the Deck