Lawn Mower Control Cables

Fix Number

FIX19305064

Manufacturer Part Number

946-04661A

This is an authentic 51-inch control cable for walk-behind lawn mowers. This part is made up of a metal wire cable with a Z-type bent end on either side, and a 37.5-inch rubberized outer cover. When the control handle is released, the control cable stops the blade. If the cable breaks, the brake will not release even after pressing the lever. To remove the old cable, cut off any cable ties, remove the cable end from the control bail, and remove the control cable from the engine (you may need pliers). Remove the cables from the openings on the handle, which can be twisted off by rotating the cable at a 90-degree angle.

★★★★★

★★★★★

1 Review

Fix Number

FIX11813377

Manufacturer Part Number

946-05124A

This is an authentic OEM part. The MTD deck engage cable is composed of metal and plastic parts, and has been designed for use in several tractor machines. This part is fastened onto the frame assembly. The deck engage cable works to move belt idler pulley and engage the cutting blades. Please refer to manual for specific repair instructions. A wrench and a screwdriver is helpful in making the replacement. This part is sold individually.

Fix Number

FIX9015022

Manufacturer Part Number

532183567

This is a lawn mower engine control cable, also sometimes referred to as a zone control cable. This part is sourced directly from the manufacturer and is sold individually. It is comprised of a metal wire with Z-type bent ends, a rubberized exterior, and a plastic clip. This part is designed to stop the engine when you release the handle. The conduit measures approximately 52.5 inches and the cable measures roughly 61.5 inches.

Fix Number

FIX9018907

Manufacturer Part Number

532427497

This is a genuine Craftsman part for use with Lawn Mowers. The zone control cable stops the engine when you let go of the handle. This part is sold individually. The most common reason for replacing the control cable is if it is broken, causing the brake to not release even when the lever is pressed. The tool that you will need to replace the zone control cable is pliers.

Fix Number

FIX8850145

Manufacturer Part Number

119-2379

This cable-traction is sourced directly from the original equipment manufacturer. It is specially designed for use with Toro lawn mowers. The traction cable engages drive wheels on the equipment. Over time it may wear out or get damaged eventually requiring a replacement. It is connected to the bail and then attached to the traction bracket near the transmission. Refer to the owners manual and the appropriate diagrams of your model for the exact location and the correct installation. One durable rubber insulated cable is included. You may need pliers and a wrench set to disconnect the old part and attach the new one.

Fix Number

FIX9019323

Manufacturer Part Number

532435111

This is a genuine replacement part sourced from the original manufacturer for use with riding mowers and lawn tractors made by Husqvarna, Weedeater, Jonsered and Poulan. This part attaches the lever to the idler arm on the mower deck and grants you access to disengage and engage the blades. This manual clutch cable includes the cable, cable sheath with connection clips and the spring hook. You will need a socket set to replace this part. This part is made of metal, rubber and wire.

Fix Number

FIX10033928

Manufacturer Part Number

946-04173E

This is an OEM deck engagement cable, sold as one part. This part is for a lawnmower and its purpose is to engage the mowers blade, allowing you to control your engine zone. It consists of a metal wire cable, a rubber cover and an extension spring on one end and a Z-bend on the other. The cable casing length is approximately 39-inches and the inner wire length is about 56-inches.

Fix Number

FIX9019379

Manufacturer Part Number

532435110

Authentic replacement part used on Husqvarna riding lawn mowers/tractors. This cable consists of a metal wire cable with z-type bent end and rubberized cover/body. The clutch cable engages the deck. You may need pliers to complete this repair. • First you want to see where the old cable is attached • Just remove the cable end there and install the new one • Now you can run the new cable up to the control handle • Then just as the old cable, put the z-shaped end through the hole in the control handle • Tie the cable in place just as the old one was, but leave enough clearance and free play to avoid over-bending and breaking the new cable

Fix Number

FIX16463572

Manufacturer Part Number

946-04728A

This is an authentic replacement part that is supplied by the original equipment manufacturer for use with walk-behind lawn mowers. The drive cable stops the engine when a user lets go of the operator presence handle. When the brake cable is damaged or broken, the mower becomes temporarily inoperable requiring a replacement cable. Please note this high-quality durable rubber insulated cable is sold individually.

★★★★★

★★★★★

1 Review

Fix Number

FIX9180334

Manufacturer Part Number

946-1130

This Genuine OEM control cable is designed to connect the control handle to the engine mechanism on compatible lawn mowers, enabling safe and responsive blade engagement. When the control handle is pressed, the cable activates the blade rotation; releasing the handle stops the blade, ensuring operator safety. This specific part features a 40-inch covered housing with a total cable length of 53 inches, including 13 inches of exposed cable. It is sold individually and includes all necessary components for straightforward replacement. Please note that part number 946-1137 features a fully covered cable with a length of 53 inches. To ensure proper fit and function, carefully compare your existing cable before ordering.