Campbell Hausfeld Parts

Fix Number

FIX17016290

Manufacturer Part Number

VT4923

Svc Compressor Pump Cw 75 X 51Mm

Fix Number

FIX10051151

Manufacturer Part Number

ST085200AV

Genuine Campbell Hausfeld replacement part, this item is sold individually. The Ferrule in this case is used on all of the compressors listed below. It is placed inside a Compression Nut of which is on a copper or aluminum tube and then attached to a component of the compressor. It aids in stopping air leaks.

Fix Number

FIX10046152

Manufacturer Part Number

GA016306AV

The purpose of a gauge is to register the pressure readings inside the tank. This replacement gauge is sourced directly from original equipment manufacturer for use with Campbell Hausfeld air compressors. The dial reads 0-250 PSI. Please note this gauge has a durable metal body and it is sold individually. You should only need a wrench and a thread-sealing tape to complete this repair.

Fix Number

FIX10044010

Manufacturer Part Number

CW218000AV

This is an authentic replacement part manufactured for use with Campbell Hausfeld pressure washers. The pressure switch is used to turn the pump on or off depending on the amount of air pressure within the tank. A faulty switch will likely prevent the pump from turning on when the pressure in the tank is low. This switch is available as an individual replacement part, please see model diagram for associative parts.

Fix Number

FIX10043938

Manufacturer Part Number

CV221502SJ

This is a high-quality OEM replacement part which is designed for use with Campbell Hausfeld air compressors. Check valve lets the pressurized air flow into the tank and prevents it from flowing back into the pump. Unfortunately, over time it may wear out or even get damaged eventually requiring a replacement to ensure your equipment functions properly. When the check valve is faulty, the compressor will initially function normally until the tank fills with air. At that point, the pump will attempt to restart, but the engine will produce only a humming noise. Similarly, if the tank is already full of air, the engine will produce only the humming noise without actually engaging. When replacing this part make sure to unplug the air compressor and release the air from the tank. It is a metal check valve and is sold individually. You would need a wrench set to disconnect and reconnect lines an perform the repair.

Fix Number

FIX10053822

Manufacturer Part Number

VH901800AV

This is a genuine OEM sourced replacement part used on Campbell Hausfeld air compressors. Its purpose is to filter out dust and debris from contaminating the engine. This filter is made out of paper and metal. This item is sold individually. To replace this you would need a wrench to remove the air cleaner cover.

Fix Number

FIX17016282

Manufacturer Part Number

BT021501AV

This is a genuine OEM approved replacement drive belt. It is supplied by original equipment manufacturer for use with Campbell Hausfeld air compressors. This is the belt that connects the pump and the electric motor. Over time these rubber belts tend to wear out and stretch eventually requiring replacement to maintain peak performance. Always make sure to clean the pulleys before installing the new belt, this will help to ensure longevity of the new belt. Includes one (1) belt per order. Replacing this belt is a very simple task that should only require a screwdriver. • Make sure to unplug the compressor and drain the tank • Remove the cover screws • Separate the cover from the unit • Remove the old belt • Clean the pulleys • Install the new belt • Secure the cover with the screws

Fix Number

FIX17016281

Manufacturer Part Number

SR060513SV

This is a genuine Campbell Hausfeld replacement drain valve, sold individually. When using an air compressor, moisture naturally condenses inside the tank. If this water is left sitting for too long, it can lead to internal rust and damage. The drain valve allows you to release this built-up moisture easily. It's especially important to drain your tank after each use—particularly if you tend to leave air in the tank for extended periods. Regular draining helps extend the life of your compressor and maintain its performance. Be sure to open the valve regularly to prevent water buildup and potential tank corrosion.

Fix Number

FIX10050276

Manufacturer Part Number

RE206203AV

This is a genuine manufacturer sourced replacement regulator. It is specially designed for Campbell Hausfeld air compressors. This part adjusts the pressure of the air coming from the tank to the desired level. Please note, this only includes the metal regulator and the plastic knob. The valves, gauges and the pressure switch are all sold separately. To complete this repair you would need an a screwdriver, pliers and a set of wrenches. • First make sure to unplug the compressor • Drain the air from the tank • Disconnect all the valves and gauges from the regulator • Remove the old regulator • Secure the new regulator assembly • Reassemble and test the new regulator

★★★★★

★★★★★

1 Review

Fix Number

FIX10043982

Manufacturer Part Number

CW209300AV

This is an OEM pressure switch for an air compressor. The pressure switch detects the pressure in the tank and controls when the unit shuts on and off. This part will need to be replaced if your air compressor is not turning on and off at the specified pressures of your unit, if it leaks, or if the copper contacts inside are corroded or burnt. This condor style pressure switch consists of four ports, a 90-degree quick-lock unloader, an on and off lever, and is 100-135 PSI.