OEM Campbell Hausfeld Nailer Parts | Expert DIY Repair Help & Fast Shipping | Fix.com

Popular Campbell Hausfeld Nailer Parts

$16.76
Head Valve Assembly Kit
(1)
Fix Number FIX10243460
Manufacturer Part Number SKN06400AV
This genuine OEM part has been sourced directly from Campbell Hausfeld. The head valve is located on the back of our nail gun; it is in the top exhaust port. Over time the o-rings get gritty, they get dirty, they wear down, and stop being effective. As the o-rings break down and start to fail air will leak out of the main exhaust system, it is at this time you should look to tune up and clean the head valve assembly. This kit includes all of the o-rings required, the piston bumper, and the head valve.
Fixes these symptoms
No Symptoms for this part
Installation Instructions
dudley from LIVINGSTON, TX says,

Framing nailer was leaking air out the exhaust port
disconnect air from nailer
Take out the four bolts holding the head assembly and remove the part
Replace with the new part
Reinstall the head on the nailer and tighten bolts
Reconn...read more

$15.67
Complete O-Ring Replacement Kit
Fix Number FIX10243560
Manufacturer Part Number SKN18600AV
This authentic OEM part has been sourced directly from Campbell Hausfeld. O-rings might seem like a very basic part, however they are essential to the function of your nail gun. O-rings seal all of the connection points and parts within your nail gun, this ensures the nail gun is maintaining pressure. If your nail gun is losing pressure it might not have the force it needs to drive a nail properly. O-rings are made of rubber, therefore over time they will get gritty, dirty, and wear down; this will make your nail gun prone to air leaks. As they become less effective so will your nail gun, this kit includes all of the o-rings you will need to keep your nail gun in tip top shape.
Fixes these symptoms
No Symptoms for this part
$4.42
Head Valve Repair Kit
(1)
Fix Number FIX10243505
Manufacturer Part Number SKN12900AV
This authentic OEM part has been sourced directly from Campbell Hausfeld. When you start to notice there is air leaking out of the exhaust port on the back of your nail gun it is a sign the nail gun is no longer holding pressure and is in need of a tune-up. On the head valve assembly there are a number of rubber o-rings, as those wear down over time they become less effective and the assembly will no longer be air tight. The same goes for the gasket on the assembly. This head valve repair kit comes with all of the o-rings, springs, and gaskets you will need for a full re-build of the head valve.
Fixes these symptoms
No Symptoms for this part
$6.33
Complete O-Ring Kit
Fix Number FIX10243504
Manufacturer Part Number SKN12800AV
Fixes these symptoms
No Symptoms for this part
$5.82
Complete O-Ring Kit
Fix Number FIX10243437
Manufacturer Part Number SKN03200AV
Fixes these symptoms
No Symptoms for this part
$23.58
Driver Kit
Fix Number FIX10243459
Manufacturer Part Number SKN06300AV
This is a genuine OEM part that has been sourced directly from Campbell Hausfeld. The driver is the part of your nail gun that forces the nail out of the gun into whatever surface you are nailing. Without a driver that is functioning properly your nail gun will not work. If you pull the trigger and nothing happens it could be a simple as a jammed nail in the driver assembly. However it is possible you have a bigger issue with your driver, it could be cracked, bent, worn out, or the end of the driver might have broken off. If this is the case you?ll need to replace your driver. One sign to look for is if the driver is no longer extending out past the end of the nailer. This kit comes with all of the parts you will need to replace the piston and driver in your nail gun.
Fixes these symptoms
No Symptoms for this part
$19.77
Pusher Assembly
Fix Number FIX10243457
Manufacturer Part Number SKN06100AV
This authentic OEM part has been sourced directly from Campbell Hausfeld. If your nail gun is skipping or misfiring, or is your nail gun cycles but no nails are coming out, then you might have a problem with the pusher assembly. This assembly is what pushes the nails along the magazine until they are fired. This pusher assembly kit includes everything you will need to properly install a new pusher mechanism into your nail gun.
Fixes these symptoms
No Symptoms for this part
Installation Instructions
kelly from ROSEBURG, OR says,

The spring of the pusher assembly split lengthwise and curled up interfering with the nail feeding process.
1. I removed the magazine from the gun (3 allen-head machine screws at the front of the magazine, and 1 on the bottom).
2. The machine screw that mounts the pusher assembly requires a slender phi...read more

$6.40
Complete O-Ring Kit
Fix Number FIX10243441
Manufacturer Part Number SKN03700AV
Fixes these symptoms
No Symptoms for this part
$8.53
Complete O-Ring Kit
Fix Number FIX10243486
Manufacturer Part Number SKN09100AV
Fixes these symptoms
No Symptoms for this part
$17.66
Complete O-Ring Kit
Fix Number FIX10243500
Manufacturer Part Number SKN10500AV
Fixes these symptoms
No Symptoms for this part

Popular Campbell Hausfeld Nailer Models