Bostitch Parts

Fix Number

FIX18997093

Manufacturer Part Number

P0590000200

This is a black circular exhaust cover for staplers or nailers. This exhaust cover is designed to allow you to direct the air in any direction you want. Please be advised that the flange nut needed to secure this cover is sold separately, so it is a good idea to check its condition and order it as needed. To install this part, you will need a hex key or Allen wrench.

★★★★★

★★★★★

1 Review

Fix Number

FIX10169875

Manufacturer Part Number

330072-98

This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

★★★★★

★★★★★

3 Reviews

Fix Number

FIX12508562

Manufacturer Part Number

N286039

This is a single OEM drain valve for an air compressor. A drain valve is a small device that is usually located at the bottom of the compressor air receiver. The drain valve can be opened or closed, and this allows water to exit the tank. Water builds up if air is left in the tank for an extended period of time, and if left for too long, it can start to rust out the inside of the tank and the drain valve can become clogged with rust or start to corrode. You should be draining the tank each time you use your air compressor to stop this from happening. This is a very quick and simple repair. Use a wrench to remove the old drain valve, and thread the new one into place by hand.

★★★★★

★★★★★

6 Reviews

Fix Number

FIX18993125

Manufacturer Part Number

N008792

This air compressor regulator repair kit restores proper pressure control and airflow by replacing worn internal components such as seals and the piston. Designed to address leaks or inconsistent pressure, it helps return the regulator to reliable working condition. Replacing damaged parts with this kit can improve performance and ensure consistent operation.

★★★★★

★★★★★

10 Reviews

Fix Number

FIX12417689

Manufacturer Part Number

180450-S

This head valve body regulates airflow within pneumatic nailers, helping generate the pressure needed to drive fasteners effectively. Built from durable materials, it supports consistent tool performance. Replacing a worn or faulty valve can resolve issues such as air leaks, reduced driving power, or failure to fire, restoring reliable operation.

Fix Number

FIX18997335

Manufacturer Part Number

S06P001500

This is a Genuine Manufacturer Sourced replacement part designed for Nailers/Staplers. This O-Ring provides an Air-Tight Seal for the Valve Piston. Over time this O-Ring will shrink, become brittle and crack allowing for air leaks. At that time it should be replaced. It is made out of Rubber and it is Sold Individually. Replacing this item you would need Hex Key/Allen Wrench and Pliers to replace this item.

Fix Number

FIX12420389

Manufacturer Part Number

180448

This is an OEM replacement O-ring for a nailer, sold individually. This O-ring is what seals the cylinder to the housing of the gun and creates separation between the upper and lower air chambers. Due to its rubber material, over time, it can wear. For this repair you will need to remove the cap, disassemble the head valve, remove the spring, and remove the old O-ring. Apply some lubrication to the new O-ring and place it on the valve.

Fix Number

FIX18992779

Manufacturer Part Number

H30624

Genuine Manufacturer Sourced replacement part used on Bostitch Stapler. This part is made out of Metal and it is Sold Individually. This Driver along with a Flat Spring are both attached with the same Screw to the Frame. Please note all parts are Sold Separately.

Fix Number

FIX18991071

Manufacturer Part Number

AC-0781

This O-ring tube seal helps create an airtight connection where the tube enters the compressor head, supporting proper pressure and efficient operation. Made from durable rubber, it is designed to withstand heat and wear during regular use. Replacing a worn or damaged seal can help prevent air leaks and restore consistent compressor performance.Provide your feedback on BizChat

Fix Number

FIX10187047

Manufacturer Part Number

N011005

This part includes one black rubber belt for a compressor. It is sourced right from the original manufacturer. Over time, the belt can become brittle and break and will need to be replaced when this happens. This belt is driven by the electric motor, and attaches to the flywheel, motor shaft and idler pulley. It measures 30-1/2-Inches long overall, 14-1/4-Inches at half length, 5/8-Inches wide, and has a thickness of 0.065-inches with teeth.