Speed Queen Washer Parts

Speed Queen Appliance Parts
Shop By Appliance Type

Popular Speed Queen Washer Parts

$7.76
  In Stock
Hose Clamp
Fix Number FIX11743008
Manufacturer Part Number WP596669
This washing machine hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
Fixes these symptoms
Installation Instructions
Albert from Unadilla, NY
noticed water was leaking in front of washer-right before we were leaving for vacation
Upon returning from vacation, we needed to do laundry-so I put some plastic under the washer and we did a load. The water was leaking from the seam between the lid and the back panel on the side with the hot and cold water connections- not the front. I removed two screws from the front bottom panel and two screws from the underside of the lid.Turning the washer on showed the leak was coming from the injection valve( it was brittle from age). The rubber injection valve was replaced and installed( using a little liquid soap to help the rubber hose to slip over the rubber injection valve) with a new clamp. The leak was fixed. Read more...
$10.76
  In Stock
Hose Clamp
Fix Number FIX11740613
Manufacturer Part Number WP285655
This hose clamp is sold individually.
Fixes these symptoms
Installation Instructions
David from Middletown, PA
Slight leak in tub drain hose
Unplug unit from electrical outlet. Remove two Phillips screws in bottom of front cover. Swing front cover up and off the washer. Loosen both hose clamps. Place a large rag (or several paper towels) around base of hose where it connects to the water pump. Gently loosen bottom of hose from water pump and remove. Gently loosen top of hose from tub drain and remove. Slide new hose top onto tub drain. Slip both new clamps onto hose (lower clamp screw should be on the inside of the hose so that there is no interference with rotating parts). Slide new hose bottom onto water pump. Tighten both clamps snuggly. Re-install front cover. Plug unit back in. Read more...
$7.76
  In Stock
Thrust Washer
Fix Number FIX11740482
Manufacturer Part Number WP233520
This washer is 3/4 inches in diameter.
Fixes these symptoms
  • Burning smell
  • Noisy
  • Pumps but will not spin
  • See more...
Installation Instructions
Ralph from Alexandria, OH
Grinding , drum flopping , .....Noise !
I won't go into all the details of the repairs .....The videos this company provides are A+++.. Some would say I would have been better off purchasing a New dryer ...LOL if I had to use a appliance repair man for this job ...Probably ...but ...using this site certified parts , and using the easy to follow instruction videos ....It was truly a very easy repair . I spent more time getting everything perfectly clean inside the dryer housing ,and letting the high temp adhesive cure than I did actually installing the parts.I can't recommend this company or the parts more ...Just take your time with removal , cleaning , and installation ....Patience !Excellent ...parts quality , shipping speed , and video installation instructions !!!! My dryer now works and SOUNDS like a new dryer ....Thank you ! Read more...
$8.85
  In Stock
Retaining Ring
Fix Number FIX11740487
Manufacturer Part Number WP23748
This metal retaining ring is well under an inch long. Use it for your Maytag brand clothes washer or your clothes dryer.
Fixes these symptoms
  • Burning smell
  • Noisy
  • Pumps but will not spin
  • See more...
Installation Instructions
Ralph from Alexandria, OH
Grinding , drum flopping , .....Noise !
I won't go into all the details of the repairs .....The videos this company provides are A+++.. Some would say I would have been better off purchasing a New dryer ...LOL if I had to use a appliance repair man for this job ...Probably ...but ...using this site certified parts , and using the easy to follow instruction videos ....It was truly a very easy repair . I spent more time getting everything perfectly clean inside the dryer housing ,and letting the high temp adhesive cure than I did actually installing the parts.I can't recommend this company or the parts more ...Just take your time with removal , cleaning , and installation ....Patience !Excellent ...parts quality , shipping speed , and video installation instructions !!!! My dryer now works and SOUNDS like a new dryer ....Thank you ! Read more...
$29.32
  In Stock
Door Switch Kit
★★★★★
★★★★★
(1)
Fix Number FIX1964648
Manufacturer Part Number W10169313
This part replaces older two terminal switches.
Fixes these symptoms
  • No heat or not enough heat
  • Noisy
  • Will not shut off
  • See more...
Installation Instructions
MATTHEW from TRION, GA
Loud Squealling While Drying
Take time to examine your machine before ordering parts, I did not need to expensive roller wheel kits , I needed two washers for the roller wheels. I pulled it apart and used the snap ring pliers to pull the roller wheels off,put the washer behind the wheel , I added a dab of hi temp grease to inside of roller and shaft. Put it back together. Quite as a new one. . The rest of the parts are straight forward . . Good luck Read more...
$50.18
  In Stock
Heating Element
Fix Number FIX11742505
Manufacturer Part Number WP4391960
This element carries 5200W and 240V. Note: This element no longer includes two terminals and two adapter leads. They must be ordered separately.
Fixes these symptoms
  • No heat or not enough heat
  • Takes too long to dry
  • See more...
Installation Instructions
Steve from South Lake Tahoe, CA
Defective heater element dryer still runs.
Expect to spend a lot of time on your knees. Unplug appliance. Remove dryer hose. remove back cover 4-6 7mm bolts. Unplug dryer heater element connections 2 blade or pin connectors. Unbolt element cover and remove old element. Label wires. Hopefully the replacement connections match if not go to hardware store. Crimp or better solder on new connectors. Install element in housing and reattach. Clean out all old dirt and lint. check old belt for wear and re-grease drum roller shafts. re-install back cover, hose and plug in. enjoy you just saved $600 Read more...
$34.04
  In Stock
V-Style Spin and Agitate Belt - 28-3/4 inches long
Fix Number FIX11740577
Manufacturer Part Number WP27001006
This v-style spin and agitate belt is 28-3/4 inches long and half of an inch wide. It is all black in color and made entirely of rubber.
Fixes these symptoms
  • Burning smell
  • Noisy
  • Pumps but will not spin
  • See more...
Installation Instructions
John from Ames, IA
Water leaking from bottom of washer, and belt burnt out due to age and overloading.
Found this youtube video of a Maytag washer that are the exact same parts and instructions to replace the water pump and belt. Fix it yourself and save! Read more...
$9.11
  In Stock
Plate Nut
Fix Number FIX11741518
Manufacturer Part Number WP3400029
$20.48
  In Stock
Spray Paint - 12 oz. - White
Fix Number FIX347819
Manufacturer Part Number 350930
$39.38
  In Stock
Spin Belt
Fix Number FIX11740578
Manufacturer Part Number WP27001007
This v-shaped spin belt helps transfer power from the motor to the transmission to help pump the water in and out of the washer. It also helps runs the spin cycle in the washer.
Fixes these symptoms
Installation Instructions
Michael from Mount Clemens, MI
Cloths still wet after cycle
Take the front panels off, there's 2 screws at the bottom of each panel. Unplug the wire harness from the back of the motor and remove the belt from the pulleys. Pay close attention to the way that the belt runs. It's a little difficult to put back on so you only want to do it once. Disconnect the water hoses from to pump. Put a towel under it a little water will come out. Unbolt the motor and remove it. I replaced the idle pulley and the belt. The pump must be removed from the motor there are 3 torx screws. The idle pulley has to be removed with snap ring pliers. Replace the belt and reassemble. Again pay close attention how the belt goes on in relation to the pump screws. Put the motor back in the washer. Another set of hands would be helpful when bolting it back in, it's awkward and there's very little room. Put the belt back on the pulleys. It's tricky be patient. Hook the hoses back up and plug in the wire harness. I ran a load just to make sure nothing leaked before I put the front panels back on. Having done it once if I had to do it again it would go much easier. Read more...

Appliance Type

Popular Speed Queen Washer Models