KitchenAid Washer Parts

KitchenAid Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular KitchenAid Washer Parts

$4.39
In Stock
Agitator Directional Cogs
★★★★★
★★★★★
19 Reviews
Fix Number FIX388034
Manufacturer Part Number 80040
Commonly referred to as dog ears, these agitator directional cogs are manufacturer approved replacement parts that come in a package of 4 and are usually used with direct drive washing machines. We recommend replacing all 4 directional cogs at the same time. The agitator directional cogs reach across the gear teeth in one direction and dig into the gear teeth in the other direction to create the needed agitation. This thrusting motion is what tumbles your clothes during the wash cycle. When the teeth on the outer edge are damaged, the cogs will not engage with the upper agitator, making it impossible to agitate as it should. If your machine makes unusual noises, shakes/moves while operating, or will not spin or drain properly, it may be time to replace them. To access this part, simply remove the softener dispenser and then the agitator cap. You will find them attached to the agitator. Each cog is approximately 1 inch long and made of a durable plastic.
Fixes these symptoms
  • Does not dispense fabric softener or detergent
  • Marks left on clothes
  • Not cleaning dishes properly
  • See more...
Installation Instructions
John from La Mesa, CA
Upper agitator stopped working
Followed the simple instructions on youtube, searching for "kenmore upper agitator doesn't work." There are a number of videos there. Find the notch on agitator cover and pry off the cover using a flat screw driver. Remove the nut in the center of the agitator using the 7/16 socket with extension. Remove upper agitator (mine came off easily but some may require removing the entire agitator, then pulling off the upper agitator). Remove assembly from inside and replace the dogs. Reassemble. Read more...
$4.93
In Stock
Suspension Spring
Fix Number FIX11743345
Manufacturer Part Number WP63907
This suspension spring is a genuine OEM replacement part for a variety of washers and washer-dryer combos. The primary purpose of the suspension spring is to support the outer tub and keep the tub steady during loads that could cause an unbalance. If this part breaks, is worn down, or has stretched out and lost its spring, it could cause the load to be off-balance which can lead to excessive shaking, moving, noise, and leaks. This part is approximately 2 inches in length when compressed, made of durable metal, and is sold individually. For this repair, you will need a 1/4 nut driver, putty knife, flat blade screwdriver, and a pair of needle-nose pliers. Before you begin, disconnect the power, fill hoses, and drain hose to give you easy and safe access (drain hose may release some water, have a small container or towel near by). Your appliance contains 3 suspension springs, so keep this in mind if you need to order multiple of this part. We suggest you purchase several at a time, as they can be very useful to have on-hand.
Fixes these symptoms
Installation Instructions
CARLOS from EL PASO, TX
just to understand the type and different model videos
exactly as the video mentioned, just need to explain if some models are alike or different using the same part numbers will be awesome.in my case my washer had the screws in different areas to disassemble and Assembly the spare parts, other than that beautiful idea in sending the link video with the email confirmation let me tell you first class and top of the line customer service rated 5 Stars Read more...
$25.34
In Stock
Agitator Repair Kit
★★★★★
★★★★★
10 Reviews
Fix Number FIX334650
Manufacturer Part Number 285811
This is an OEM agitator repair kit that includes an agitator cam, four directional cogs, a bearing, thrust spacer, inner cap seal, and washer. These parts are found inside the agitator auger near the top. This kit is used when the top portion of the agitator is not moving correctly but the bottom part is. The agitator is subjected to a lot of force during the wash cycle, so it is common for this part to wear over time, especially if you are consistently over-loading your washer. If your model has a softener dispenser, it will need to be removed to perform this repair. Agitator grease is recommended for this repair, but is not included in this kit.
Fixes these symptoms
  • Does not dispense fabric softener or detergent
  • Leaking
  • Marks left on clothes
  • See more...
Installation Instructions
Jerry from Aransas Pass, TX
Agitator not working correctly and leaking from somewhere underneath.
I watched the videos before I ordered the part and when the order arrived I replaced the parts with no problems. The most time consuming part of the job was cleaning the washer. You will be surprised to find what will accumulate down there after years of service. The order came in in record time so this site gets an A+ for being fast and accurate. No back-orders either. I will surely use for any-other parts I need in the future. Read more...
$27.87
In Stock
Direct Drive Motor Coupling
★★★★★
★★★★★
7 Reviews
Fix Number FIX1485646
Manufacturer Part Number 285753A
This is an OEM direct drive motor coupling, which provides a cushioned connection between the transmission and the motor shaft. This is the newer version of this part, made with new metal sleeves for added strength. It is located between the motor and transmission on direct drive washers with no belt. If the drive system seizes, the coupling is designed to break to prevent the drive motor from damage. Consequently, this part may need to be replaced as your appliance ages. Never overload your washer, as this can speed up its deterioration. Symptoms of a faulty motor coupling include a washer pumping but not spinning, slow spinning, the washer not agitating, and unusual noises. This coupling kit contains all the parts necessary to replace your existing direct drive motor coupling. Please note, that after replacing the motor coupling your washer may smell like burning rubber for the first few uses, this is entirely normal as the part becomes acclimated to the machine. Each is sold individually.
Fixes these symptoms
Installation Instructions
Joseph from Burnsville, NC
Washer would not spin or agitate
First, I found it very easy to follow the help on your web site to determine the most likely parts that would cause my problems. The direct drive motor coupling could be the cause of both problems. Also the agitator repair kit was the most likely cause of the agitator problem, So, I ordered both parts. When AI received the parts there were videos included instructing every detail for installation. I just followed the video for the direct drive motor coupling and both problems were solved with the one part. It took about 30 minutes and was a simple installation. .Thanks for your good service. It saved me a service call or maybe a new washer and dryer set. Read more...
$50.03
In Stock
Clutch Assembly
Fix Number FIX334641
Manufacturer Part Number 285785
This is a genuine OEM replacement clutch assembly for your washing machine. A clutch assembly, also known as a clutch or a washer clutch, is responsible for spinning the tub during the spin cycle. If the clutch becomes worn and is no longer operating properly, your clothes will remain soaked after the cycle is finished. Some other signs it is time to replace the clutch is if your washer is noisy while running, there is a burning smell, or the machine is shaking excessively. This kit comes with the clutch, brake cam driver, spring, retaining ring, and a nylon anti-rattle clip. Before beginning this repair, be sure to disconnect the power and water supply to your machine. Depending on your washer model, you may need an additional person to help lower the machine onto its back, as access to the drive shaft to change the clutch assembly may be easiest through the bottom of the appliance.
Fixes these symptoms
  • Burning smell
  • Spinning Issues
  • Spins slowly
  • See more...
Installation Instructions
Paul from Mobile, AL
would not spin
well i replaced a lot of parts..but i think it was the the lid switch. but now its brand new..Thanks Read more...
$7.04
In Stock
Agitator Bolt
Fix Number FIX11741866
Manufacturer Part Number WP358237
This bolt is a genuine OEM replacement part, used to secure the agitator in your washing machine. Overtime the bolt can become worn out due to the vibrations of the washer, and will need to be replaced. The size of the screw head is 7/16 inch, so you will need the appropriately sized socket to complete this repair. The new bolt comes with a rubber gasket and a threaded sealant.
Fixes these symptoms
  • Leaking
  • Marks left on clothes
  • Spins slowly
  • See more...
Installation Instructions
Jerry from Aransas Pass, TX
Agitator not working correctly and leaking from somewhere underneath.
I watched the videos before I ordered the part and when the order arrived I replaced the parts with no problems. The most time consuming part of the job was cleaning the washer. You will be surprised to find what will accumulate down there after years of service. The order came in in record time so this site gets an A+ for being fast and accurate. No back-orders either. I will surely use for any-other parts I need in the future. Read more...
$35.28
In Stock
Water Inlet Valve with Mounting Bracket
★★★★★
★★★★★
2 Reviews
Fix Number FIX334646
Manufacturer Part Number 285805
There are many symptoms that may indicate an issue with your water inlet valve. These can include your washer not filling with water, it will not stop filling, the washer is leaking, or it is both filling and draining at the same time. You can test if your valve is faulty two different ways. The first is to disconnect the power while the washer fills, if water continues to fill the tub, then the valve should be replaced. The second way is to use a multimeter to test for continuity on the valve solenoids. If you do need to replace the water inlet valve, this is a genuine OEM part that has two ports and is compatible with half-inch ID hose. Before beginning your repair, please be sure to disconnect the power and water supply to your washing machine.
Fixes these symptoms
Installation Instructions
Carol from Shawnee, KS
Only a small trickle of only cold water was filling the tub
We watched the video repair and the part went on as slick as can be and bingo like magic the tub was filling very, very fast with warm, hot, cold water depending on our setting!! Oh my goodness! It was so easy and saved us from buying a new washer and it cost $15!!!! I am so excited!!! I get the was done in a tenth of the time!! Thanks for your parts and videos!! Read more...
$7.04
In Stock
Tub Spring
Fix Number FIX11751118
Manufacturer Part Number WPW10250667
This tub spring is a genuine OEM replacement part for your washing machine and is sold individually. There are other names that the tub spring goes by, such as the suspension spring, balance spring, or counterweight spring. The purpose of this spring is to ensure that the tub sits straight during the spin cycle, and it does this by counterbalancing the weight of the motor. If the spring has broken, it will cause the tub to be off-balance, which can make the washer shake and become noisy when spinning. An off-balance tub can also cause damage to other components of your washer, so it should be fixed quickly. If your model of washing machine has more than one tub spring, they should all be replaced at the same time as they tend to wear evenly. The tools you will need to complete this repair are a pair of pliers, a Philips screwdriver, and a flat blade screwdriver. Please be sure to disconnect the power supply to your washer before beginning this repair.
Fixes these symptoms
Installation Instructions
CARLOS from EL PASO, TX
just to understand the type and different model videos
exactly as the video mentioned, just need to explain if some models are alike or different using the same part numbers will be awesome.in my case my washer had the screws in different areas to disassemble and Assembly the spare parts, other than that beautiful idea in sending the link video with the email confirmation let me tell you first class and top of the line customer service rated 5 Stars Read more...
$7.45
In Stock
Foot, Front - Single
Fix Number FIX11747965
Manufacturer Part Number WPW10001130
Sold Individually.
Installation Instructions
Margaret from McLeansville, NC
Washing Machine Out of Balance - Missing Leveling Feet
The was an extremely simple repair. Tilted the washer up, placed the nut on the level foot, inserted the leveling foot in the slot and voila! Done. Absolute easiest repair ever. Read more...
$7.95
In Stock
Hose Clamp
Fix Number FIX11743008
Manufacturer Part Number WP596669
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
Fixes these symptoms
Installation Instructions
Albert from Unadilla, NY
noticed water was leaking in front of washer-right before we were leaving for vacation
Upon returning from vacation, we needed to do laundry-so I put some plastic under the washer and we did a load. The water was leaking from the seam between the lid and the back panel on the side with the hot and cold water connections- not the front. I removed two screws from the front bottom panel and two screws from the underside of the lid.Turning the washer on showed the leak was coming from the injection valve( it was brittle from age). The rubber injection valve was replaced and installed( using a little liquid soap to help the rubber hose to slip over the rubber injection valve) with a new clamp. The leak was fixed. Read more...

Appliance Type

Related Pages

Popular KitchenAid Washer Models