Roper Washer Dryer Combo Hardware

Fix Number

FIX11755850

Manufacturer Part Number

WPW10512946

This small but mighty OEM piece is called a tri-ring and is used to support the drum roller shaft and the idler pulley shaft in your dryer. It helps to provide a tight seal between components by evenly distributing pressure. The part is triangular in shape, and less than an inch in size. Overtime it can become brittle or compressed, which can lead to a noisy tumbling cycle, or your dryer not tumbling at all. The tri-ring itself is simple to replace, simply slip off the damaged one and slip on the new. However, to access the drum roller or idler pulley, you will need to remove the front panel and drum of your dryer. This may require tools like a Phillips screwdriver, a quarter inch nut driver, putty knife, a small flat blade screwdriver, and a pair of needle nose pliers depending on your model. Ensure that the power is disconnected before beginning your repair.

★★★★★

★★★★★

1 Review

Fix Number

FIX334180

Manufacturer Part Number

279311

This is a genuine OEM replacement igniter kit for your gas-heated clothes dryer. The silicon carbide igniter is used to light the gas that creates the heat in order to dry your clothes. If your dryer is not heating, takes a long time to dry clothes, or has low heat you may want to consider replacing your igniter. This kit can be used to replace both round and flat igniters, and comes with a 3-inch flat igniter, bracket, 4-inch wire lead, and the plug. Before beginning this repair, please ensure that the power and gas is disconnected from the range. As the igniter is located within the burner assembly, you will need a variety of tools to complete the installation. These tools include a putty knife, a small flat blade screwdriver, a 5/16 nut driver, and a 5/16 socket with a ratchet. This part should be handled with care, as the igniter is very fragile.

Fix Number

FIX11741866

Manufacturer Part Number

WP358237

This bolt is a genuine OEM replacement part, used to secure the agitator in your washing machine. Overtime the bolt can become worn out due to the vibrations of the washer, and will need to be replaced. The size of the screw head is 7/16 inch, so you will need the appropriately sized socket to complete this repair. The new bolt comes with a rubber gasket and a threaded sealant.

Fix Number

FIX11731288

Manufacturer Part Number

W10854425

This part is the replacement single front panel clip for your dryer. It is made of metal and is approximately 2 inches long and ¾ inch wide. The front panel retainer clip is what holds the front panel on to the dryer. If the clip is damaged or missing, or if the front panel appears loose, you may need to replace the clip. This part is sold individually and is an authentic OEM part.

Fix Number

FIX11740701

Manufacturer Part Number

WP308685

This is a multi-use cover screw. It fits appliances such as dryers, ranges, washers, dishwashers, refrigerators, air conditioners, washer dryer combos, freezers, wall ovens, microwaves, dehumidifiers, cooktops, trash compactors, grills, and ice makers. *Please note: This part is sold individually.

Fix Number

FIX11743008

Manufacturer Part Number

WP596669

This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.

Fix Number

FIX11741612

Manufacturer Part Number

WP3400882

This screw is sold individually.

Fix Number

FIX11746840

Manufacturer Part Number

WP90767

This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the manufacturer for further repair guidance.

Fix Number

FIX11741763

Manufacturer Part Number

WP348197

Fix Number

FIX341974

Manufacturer Part Number

3360629

This is used in your direct drive washer that has a neutral drain.