Kenmore Trash Compactor Parts
Start With Your Model Number
Find Parts Fast
Guaranteed Fit
Repair Videos
Need help finding your model number?

Popular Kenmore Trash Compactor Parts
Drive Gear Kit
Fix Number FIX398589
Manufacturer Part Number 882699
This is a genuine OEM drive gear kit for your trash compactor. It includes the drive gear, pin spring, a retaining clip which is also known as a c-ring, ram stop, and the ram cam. The ram is used to compact the trash and if it is getting stuck, making excess noise, or is not stopping at the end of the cycle, then the drive gear may need to be replaced. Before beginning this repair, please be sure to disconnect the power supply to the trash compactor.
Fixes these symptoms
- Compactor ram gets stuck
- Doesn’t stop at end of compacting cycle
- Noisy
- See more...
Installation Instructions
John from RUTHERFORD, NJ
Trash compactor ram was not working.
Watched the video and followed the directions step by step.
Read more...
15 Inch Compactor Bags - 15 Pack
Fix Number FIX1964579
Manufacturer Part Number W10165295RP
These bags will fit most 15" rectangular compactors.
$4.31
In Stock
Door Catch Kit
Fix Number FIX334230
Manufacturer Part Number 279570
This kit includes two door strikes, and three door catches, to service doors that have one or two catches. The strike is mounted on the body of the dryer, while the catch is mounted on the dryer door. These two parts work together to keep the dryer door shut while in operation. If your appliances lid will not close, or it will not start, it may be time to replace the door catch. If this part is malfunctioning, it should be replaced immediately, as it is not safe to run a dryer with the door not properly closed. This kit also comes with a set of instructions to help with the repair.
Fixes these symptoms
- Door Pops Open
- Door won’t close
- Lid or door won’t close
- See more...
Installation Instructions
jeffrey from Brookhaven, PA
Dryer would run, but not heat
Needed it running quick, so no diagnostics. Ordered one of everything that could fix problem (plus a new door catch). Tipped it onto it's back & popped the bottom cover off. Element, thermal cutoff, thermistor, and fuse. were right in front and held by 2 screws each (don't drop them, don't ask). A little bit tight inside, but no big issue. vacuumed the inside, replaced everything (it was the Heating Element, by the way), slapped the cover on, and put it back in its spot. works like it was new. Yes, I unplugged it first. Remember! Safety Third!
Read more...
$7.45
In Stock
Foot, Front - Single
Fix Number FIX11747965
Manufacturer Part Number WPW10001130
Sold Individually.
Installation Instructions
Margaret from McLeansville, NC
Washing Machine Out of Balance - Missing Leveling Feet
The was an extremely simple repair. Tilted the washer up, placed the nut on the level foot, inserted the leveling foot in the slot and voila! Done. Absolute easiest repair ever.
Read more...
Touch-Up Paint - White
Fix Number FIX385132
Manufacturer Part Number 72017
18ml
Installation Instructions
Al from Cape Coral, FL
No heat when trying to dry clothes .
Followed instructions on your videos. Everything went as planned and the dryer works like new....
Read more...
Drawer Roller
Fix Number FIX11747573
Manufacturer Part Number WP9871602
This is a genuine OEM replacement part. This bearing roller is commonly used in the assembly of trash compactors, it allows you to easily slide the container out of the appliance. If the drawer becomes challenging to open or close it could be an issue with the roller. There is one located on each side of the compactor, however these are sold individually. Before repairing your appliance disconnect it from the power source.
Fixes these symptoms
- Drawer is hard to open and or close
- See more...
Installation Instructions
Ben from Howell, MI
Trash Compactor the drawer was very hard to open
In replacing the old partial rusted drawer slides had rusted screw with nuts that spun had to drill them out and replaced front larger bolt and nut the rear screw used a larger sheet metal screw. The wheels and bearing with on easy the instructions showed a modification to remove a tab for the different wheel assembly and installed just like the instructions. When done the drawer will slide out with just touch of your foot on open tab GREAT!! I was looking at buying a new compactor the repair saved me about 700 $. Thanks a lot. Never had a trash Compactor before this great and it keeps my puppy out of trash.
Read more...
Drive Motor
Fix Number FIX3652693
Manufacturer Part Number W10439651
This motor operates the trash compactor press that helps compacts the trash.
Installation Instructions
Scott from Derby, KS
Motor Failed On Unit
New motor arrives and is designed as a replacement across several models. It was necessary to replace all the wire end and crimp on the supplied smaller spade terminals. Only issue was the wire length on the unit was short and made it tough to reach. Followed the instructions for placement and result was great. Took me about 21/2 hours to complete
Read more...
Wheel Assembly - Kit of 2
Fix Number FIX398587
Manufacturer Part Number 882688
This is an OEM part sourced directly from the manufacturer. This wheel assembly kit is for use with trash compactors. The kit included two wheel bearings. These bearings allow the container drawer to slide out of the compactor with ease. There is one installed on each sides of the compactor, located at the base of the frame. Before repairing your appliance make sure it is unplugged.
Fixes these symptoms
- Drawer is hard to open and or close
- See more...
Installation Instructions
James from Anchorage, AK
The bar that the rollers fit into has a lip on the front.
The lip on the front of the bar had to be bent so it was almost straight out so a wrench could be put on the nut to remove the old roller. There was not room enough to get on the nut with pliers or wrench and turn it. much more difficult than the instructions laid out.
Read more...
Rotary Switch Kit
Fix Number FIX382679
Manufacturer Part Number 675382
This kit comes with an on-off rotary switch and two chrome knobs.
Fixes these symptoms
- Doesn’t stop at end of compacting cycle
- Won’t start
- Won’t stay on
- See more...
Installation Instructions
Kenneth from New Tazewell, TN
Quit after 38 years. Suggested a switch (s) failure
Removed two screws on front panel which allowed panel to become easily reachable. Replacement of rotary switch kit very simple. Did not replace sectional switch at this time. Back in operation.
Read more...
Directional Switch
Fix Number FIX11744742
Manufacturer Part Number WP777811
This is an OEM part sourced directly from the manufacturer. This is a top limit and directional switch that is designed for use with trash compactors. This switch will interrupt the current that flows to the motor when the ram reaches the top of the compactor. When the ram reaches the top of the compactor this switch reverses the motor direction. You may have a problem with your switch if you compactor won?t stop running at the end of the cycle. Before you replace this part make sure you have unplugged your trash compactor.
Fixes these symptoms
- Compactor ram gets stuck
- Doesn’t stop at end of compacting cycle
- Noisy
- See more...
Installation Instructions
Chad from Moreno Valley, CA
Trash Compactor would not stop after cycle and would make a ton of noise
I had a couple of problems with my trash compactor, it was present in the home when we bought it. First it wouldn't turn on, the on/off switch was broken so I replaced the switch and knob assembly. Then the unit would run through a cycle and wouldn't stop at the end and would make a loud banging noise. My directional switch was the suspect at first because it was in bad shape to begin with, looked like it had gotten stuck at some point and bent the arm. I replaced the directional switch and it didn't help. Then I realized that the on/off/start panel showed that the start button was stuck in the on position. This was delivering constant current and wouldn't allow the unit to stop. DON'T spend $150 for a new start/on/off panel. I took the panel off and separated the front from the back to expose the buttons from the inside. The start button was stuck so I took the parts out and reassembled them, they're all little plastic and metal pieces that interlink. After I reassembled the buttons' insides I reassembled the panel and reinstalled it. The unit works fine now.
Read more...
Appliance Type
Related Pages
Popular Kenmore Trash Compactor Models
- 66513605790
- 66513619101 COMPACTOR
- 66513612101 COMPACTOR
- 66513613101 COMPACTOR
- 66513601790
- 66513619100
- 66514733111 COMPACTOR
- 66513612100
- 6651350593
- 6651350590
- 66513613100
- 6651350596
- 6651350594
- 66513633100 Kenmore Trash Compactor Model 665.13633100 (66513633100, 665 13633100) Parts
- 66513614101 COMPACTOR
- 6651398581
- 6651350193
- 66514722113 COMPACTOR
- 66513604000
- 66514729113 COMPACTOR