General Electric Range Parts

Start With Your Model Number

Need help finding your model number?
Find Parts Fast
Guaranteed Fit
Repair Videos
Fix.com search
General Electric Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular General Electric Range Parts

Watch the install video
Drive Belt – Part Number: WE03X29897
Drive Belt
$36.13
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX16542496
Manufacturer Part Number
WE03X29897
This 89.5-inch drive belt is for dryers. It has a 4-rib design on the inside for a better grip. If comparing the size of your current belt to the new one, keep in mind that a small amount of stretching and contortion will occur over time, and this belt will fit despite small inaccuracies. You will find this part wrapped all the way around the dryer drum, around a tension pulley, and around the drive motor pulley. This allows the parts to work together to spin the drum as the motor rotates. A common symptom of a broken drive belt is a drum that will not turn. This part is prone to wear and tear over time and will likely stretch or become brittle, leading to complete breakage of the part. The drum cannot spin without a drive belt, so it needs to be replaced immediately. For this repair, we recommend wearing work gloves to protect your hands from sharp edges, disconnect the power, remove the main panel, and access the motor drive to secure the new belt in place.
Fixes these symptoms

Installation Instructions

Nae from BRENTWOOD, TN
The dry was making a whining sound. Very loud.
I followed all the video on the website with all the parts I had purchased. Very easy. Just make sure you unplug the dryer first. Thank you, Read more...
Watch the install video
Terminal Block Kit – Part Number: 5303935058
Terminal Block Kit
$16.24
In Stock
Fix Number
FIX470125
Manufacturer Part Number
5303935058
This kit comes with the necessary components to replace your burner terminal block. It includes interchangeable mounting brackets, a terminal box, ceramic wire nuts, heat shrink protective tubing, and wires. The purpose of this part is to connect the wire harness to the surface element, which allows for the burners to heat up. Some common issues that result from a damaged terminal block is that your element will not heat properly or not heat up at all, may cause burning smell, or make a buzzing noise. If you remove the element and the tips are black, that is a good sign there is a problem with the terminal block and it should be replaced. It may also be necessary to replace the burner elements as well, if the tips are badly damaged. This repair will require a pair of wire strippers, a #1 square head screwdriver, and a heat gun or hair dryer. If you are not comfortable with cutting, stripping, and reconnecting of wires you should contact a qualified professional to complete this repair. Please be sure to disconnect the power supply to your appliance before starting this repair. As this is a genuine OEM parts kit, it will be compatible with your appliance model.
Fixes these symptoms
  • Element will not heat
  • Oven not heating evenly
  • Will Not Start
  • See more...

Installation Instructions

SHIRLEY O from boxborough, MA
burner would not heat
removed burners, cut wires to each burner, installed new wires from terminal block kit. reinstalled surface element. Followed directions from video located at site of the ordered items Read more...
Watch the install video
Drum Bearing Slide - Green (Sold individually) – Part Number: WE1M1067
Drum Bearing Slide - Green (Sold individually)
$14.29
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX6447706
Manufacturer Part Number
WE1M1067
This single drum bearing slide is an OEM approved replacement part for dryers. It can also be known as a bearing drum slide, pad, or glide. The slides attach to the inner most slots on the front bearing. As the dryer rotates, the drum bearing slides help to support the front of the drum. If your appliance becomes noisy, is not drying properly, or leaves marks on clothes, it may be time to replace it. If you are replacing one slide, we recommend replacing the other slide at the same time, as they deteriorate at a similar rate. You will need to order 2 of these parts as there are 2 in each dryer. It is approximately 2.6-inches deep, 0.06-inches in height, and 0.5-inches wide. This part is denoted as being green in the title, however users and technicians have noted it is actually gray in color.
Fixes these symptoms

Installation Instructions

Donald L. from Belmont, MA
Dark marks on clothing; clothing sticking between drum and front panel
Others with the same problem of dark marks on clothing suggested replacing the white and the grey drum slides that slip into the front drum bearing unit. When I open up the dryer, I did find that both the white and grey drum slides on one side of the front drum bearing piece had completely worn away, and some of the drum bearing piece was also worn away. I had decided in advance to order both white slides, both grey slides, a new felt seal, and the front drum bearing piece. Possibly I could have reused the old front drum bearing, but the replacement was cheap enough. Three bits of advice: 1) if you replace the felt seal, make sure you get it tucked behind the clips on the door panel; 2) if you replace the front drum bearing piece, once you have the dryer put back together, reach up and pull the plastic drum bearing toward you to be sure it is fully snapped into place; 3) after you replace the slides or felt, the drum will make mild rubbing noises as it turns, so run the dryer with no heat for about 30 minutes to seat the parts. Read more...
Watch the install video
Drum Bearing Slide - White (Sold individually) – Part Number: WE1M504
Drum Bearing Slide - White (Sold individually)
$18.58
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX755842
Manufacturer Part Number
WE1M504
This single drum bearing slide attaches to the outer-most side of the bearing. This part is also sometimes referred to as a drum slide, drum glide, or drum pad. It provides support to the front of the drum as it rotates. They are approximately 3-inches long, 1 inch wide and made from a durable white plastic. If your appliance starts making unusual sounds, is not drying clothes properly, or leaves marks on clothes, it may be time to replace this part. The dryer has 2 slides, which we recommend replacing at the same time, as they tend to wear out at the same rate. You will need to order 2 of this part to replace both drum bearing slides, since it is sold individually. Before you begin this repair, be sure to disconnect the power to the dryer.
Fixes these symptoms

Installation Instructions

Donald L. from Belmont, MA
Dark marks on clothing; clothing sticking between drum and front panel
Others with the same problem of dark marks on clothing suggested replacing the white and the grey drum slides that slip into the front drum bearing unit. When I open up the dryer, I did find that both the white and grey drum slides on one side of the front drum bearing piece had completely worn away, and some of the drum bearing piece was also worn away. I had decided in advance to order both white slides, both grey slides, a new felt seal, and the front drum bearing piece. Possibly I could have reused the old front drum bearing, but the replacement was cheap enough. Three bits of advice: 1) if you replace the felt seal, make sure you get it tucked behind the clips on the door panel; 2) if you replace the front drum bearing piece, once you have the dryer put back together, reach up and pull the plastic drum bearing toward you to be sure it is fully snapped into place; 3) after you replace the slides or felt, the drum will make mild rubbing noises as it turns, so run the dryer with no heat for about 30 minutes to seat the parts. Read more...
LOWER RACK ROLLER – Part Number: WD12X26146
LOWER RACK ROLLER
$13.13
In Stock
Fix Number
FIX16217024
Manufacturer Part Number
WD12X26146
The roller helps the lower rack of your dishwasher to smoothly slide in and out of your appliance. A broken or worn roller wheel can make it clunky or difficult to get the rack in and out of the dishwasher, and the part should be replaced. The rollers are sold individually, however there are four in total in your dishwasher. You may want to replace all at the same time to ensure they have even wear. Replacing a broken roller is a simple job and may require the use of a flat blade screwdriver. Remove the entire lower rack from your dishwasher and place it on a suitable work surface. Release the tabs to open the cover on the roller assembly, using the screwdriver if necessary to pry them open. Pull the damaged wheel off the assembly and push the new one into place. Reattached the cover and place the rack back into the bottom of your dishwasher. The lower rack should now easily glide in and out. These rollers are genuine OEM parts that measure approximately 1.5 inches in diameter and are charcoal in color.
Watch the install video
Surface Element - 8 Inch - 2600W – Part Number: 316442301
Surface Element - 8 Inch - 2600W
$20.39
In Stock
Fix Number
FIX2339242
Manufacturer Part Number
316442301
The surface elements provide heat for cooking on the top your range, typically in a smaller and larger size to fit your various pots and pans. If an element is not heating up, it is a sign that it should be replaced. This is an easy repair that does not require any tools. Before beginning this repair, ensure that the elements are turned off and cold to the touch. With the element removed, inspect the terminals for signs of corrosion or arcing. If these are present, you will need to replace the terminal block as well, or you will have the same issues come up again. This OEM replacement part measures 8 inches in diameter with five coils.
Fixes these symptoms

Installation Instructions

SHIRLEY O from boxborough, MA
burner would not heat
removed burners, cut wires to each burner, installed new wires from terminal block kit. reinstalled surface element. Followed directions from video located at site of the ordered items Read more...
Refrigerator Water Filter – Part Number: RPWFE
Refrigerator Water Filter
$92.40
In Stock
Fix Number
FIX10063209
Manufacturer Part Number
RPWFE
This NSF-certified water filter helps to improve the taste, quality, and health of your water by removing a number of contaminants including mercury, lead, and trace pharmaceuticals. The filter should be replaced every six month or after 300 gallons of water have been filtered. If you are unsure if your filter is due for replacement, another indicator is if the water flow from the dispenser has slowed down considerably. Replacing this part is a simple task that does not require any tools or shutting off the water or power supply to your fridge. Once the new filter has been installed, be sure to run at least two gallons of water through before consuming.
Fixes these symptoms
  • Ice maker not making ice
  • Not dispensing water
  • See more...
Watch the install video
Front Drum Bearing – Part Number: WE3M26
Front Drum Bearing
$34.14
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX960316
Manufacturer Part Number
WE3M26
Located on the inside of the dryer front panel, the front drum bearing helps your appliance to operate as quietly as possible. It allows the front of the drum to glide smoothly on the felt seal of the front panel when the drum is rotating. This manufacturer-approved part is made of a durable white plastic and measures approximately 9 inches by 20 inches. If your dryer makes a continuous banging noise while it is powered on, it is likely that the drum bearings need to be replaced. Keep in mind that the drum slides should be replaced at the same and will need to be purchased separately (the front drum bearing holds 4 glides), as this part includes the bearing only.
Fixes these symptoms

Installation Instructions

Donald L. from Belmont, MA
Dark marks on clothing; clothing sticking between drum and front panel
Others with the same problem of dark marks on clothing suggested replacing the white and the grey drum slides that slip into the front drum bearing unit. When I open up the dryer, I did find that both the white and grey drum slides on one side of the front drum bearing piece had completely worn away, and some of the drum bearing piece was also worn away. I had decided in advance to order both white slides, both grey slides, a new felt seal, and the front drum bearing piece. Possibly I could have reused the old front drum bearing, but the replacement was cheap enough. Three bits of advice: 1) if you replace the felt seal, make sure you get it tucked behind the clips on the door panel; 2) if you replace the front drum bearing piece, once you have the dryer put back together, reach up and pull the plastic drum bearing toward you to be sure it is fully snapped into place; 3) after you replace the slides or felt, the drum will make mild rubbing noises as it turns, so run the dryer with no heat for about 30 minutes to seat the parts. Read more...
Watch the install video
Light Bulb – Part Number: 316538904
Light Bulb
$19.73
In Stock
Fix Number
FIX12751166
Manufacturer Part Number
316538904
Clear, 120 Volt, 40 Watt.

Installation Instructions

Chris from Lillington, NC
Broken bake element & light bulb
Turned of the power at the fuse box as the oven was hard wired to the electrical source and then removed the old element via the screws at the back of the oven. Disconnected the wires from the element and then reconnected those to the new element. Screwed the element base to the back wall of the oven and then replaced the light bulb. Read more...
Watch the install video
Upper Rack Assembly – Part Number: WD28X30219
Upper Rack Assembly
$82.29
In Stock
Fix Number
FIX16618975
Manufacturer Part Number
WD28X30219
This dishrack is for dishwashers. The dishrack holds the dishes in place during the dishwashing cycle. Follow the instructions in the manual when installing this part.
Fixes these symptoms

Appliance Type

Related Pages

Popular General Electric Range Models

View More
+