Admiral Range Parts

Start With Your Model Number

Need help finding your model number?
Find Parts Fast
Guaranteed Fit
Repair Videos
Fix.com search
Admiral Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular Admiral Range Parts

Watch the install video
Light Bulb – Part Number: 316538904
Light Bulb
$23.95
In Stock
Fix Number
FIX12751166
Manufacturer Part Number
316538904
This 40-watt light bulb has a standard screw-in base and is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM part and is sold individually.

Installation Instructions

Chris from Lillington, NC
Broken bake element & light bulb
Turned of the power at the fuse box as the oven was hard wired to the electrical source and then removed the old element via the screws at the back of the oven. Disconnected the wires from the element and then reconnected those to the new element. Screwed the element base to the back wall of the oven and then replaced the light bulb. Read more...
Watch the install video
Chrome Drip Bowl - 8 inch – Part Number: WPW10196405
Chrome Drip Bowl - 8 inch
$10.95
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX11750107
Manufacturer Part Number
WPW10196405
This chrome drip bowl is an OEM approved replacement part sourced directly from the manufacturer. Drip bowls are a part for your cooktop, positioned underneath the burner to catch spills. This drip bowl fits under 8-inch burner elements and has a diameter of approximately 10-inches. It is common for the manufacturer to switch up designs, so it may not match your current part, however searching using the correct model number will ensure proper fit and function. Drips bowls are prone to wear and tear and can be a fire hazard if not replaced when needed. It is also a quick, easy, and cheap way to give your appliance a fresh new look. Each drip bowl is sold individually, so if you are interested in replacing your other drips bowls, they need to be ordered separately. This is also an opportune time to inspect the terminals for corrosion or damage, and the condition of the burner. No tools are required for installation, simply line up the hole on the bowl with the terminal block and drop it into place. Give your new drip bowl a regular cleaning with warm water and soap to help it last as long as possible.
Fixes these symptoms

Installation Instructions

Henry from St Louis, MO
Replace old drip Bowls
Remove heating elements, remove old drip bowl, install new drip bowls replace heating elements. Read more...
Watch the install video
Rear Drawer Glide – Part Number: 3051163
Rear Drawer Glide
$7.95
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX434227
Manufacturer Part Number
3051163
If you are having difficulty opening or closing the drawer at the bottom of your range, the drawer glides may be damaged. These genuine OEM rear drawer glides help to support the side of the drawer and prevent metal-to-metal contact when the drawer is pulled in and out. Replacing the part is an easy repair, and just requires a flat blade screwdriver. Remove the drawer from the bottom of your range and place it on a suitable work surface. Remove the broken drawer glide by disengaging the locking tab with the screwdriver. Snap the new drawer glide into place and put the drawer back in the bottom of your range, ensuring that the tracks are lined up. The drawer should now slide in easily. Please note that these parts are sold individually, but your drawer requires four glides ? one for each corner. If you need to replace more than one drawer glide, make sure you add the correct quantity to your cart.
Fixes these symptoms

Installation Instructions

Nelson E. Holley from Pottsville, PA
broken rear drawer glide
snap it out and snap it in. Read more...
Watch the install video
Light Bulb - 40W – Part Number: 8009
Light Bulb - 40W
$17.75
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX884734
Manufacturer Part Number
8009
This is a genuine OEM 40-Watt replacement light bulb that is compatible with various types of appliances. It has a frosted glass bulb with a standard metal socket base, making it easy to screw and unscrew by hand to replace. It is designed to tolerate extreme temperatures, which is why it is commonly used to light the inside of refrigerators and ovens. Depending on the appliance and location of the bulb, disconnecting the power is recommended. This bulb is sold individually.

Installation Instructions

Helen from Quincy, MA
lightbulb in refrigerator went out
Removed plastic shield on top of refrigerator. Removed old bulb.. Replaced new bulb. Reinstalled plastic shield. Voila! Read more...
Range Surface Burner Plug-In Block Kit – Part Number: 330031
Range Surface Burner Plug-In Block Kit
$15.65
In Stock
★★★★★
★★★★★
4 Reviews
Fix Number
FIX340571
Manufacturer Part Number
330031
This is a genuine OEM replacement part. This surface burner plug-in block kit is designed for use with surface elements of your ranges and cooktops. This kit helps connect the wire harness to the surface element. If your element is not heating, or if it only heats intermittently you may have an issue with your terminal block. This is a newer-style terminal block kit, it includes the plastic receptacle block, two metal brackets, two pre-crimped hi-temp wire leads with terminals, two ceramic nuts, two screws, and heat shrinking insulators. Before beginning this repair make sure you have unplugged your appliance.
Fixes these symptoms

Installation Instructions

Doris from Skoke, IL
Elements heat sporatically
I followed the steps in the instructions which were very easy, once the electric power was turned off to the range. I replaced 2 burner plug in blocks in less than 30 minutes. I am embarrassed to say that these burners have not been functional for almost 3 years. I thought that I could not work with electric. Just make sure you have the tools on hand and read the instructions first. I am a mid-50's female, if I can do this so can anyone else! Read more...
Watch the install video
Oven Bake Element – Part Number: 316075103
Oven Bake Element
$32.95
In Stock
★★★★★
★★★★★
10 Reviews
Fix Number
FIX438018
Manufacturer Part Number
316075103
This genuine OEM bake element is located on the bottom of the oven cavity to supply heat for baking. The approximate size is 19-1/2 inches wide by 18-1/2 inches long and has 3-1/2 inch inserts. The element terminals are male quarter inch spade connectors and have push-on wire terminals. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. Please remember to disconnect the power to your oven before you start your repair. Next, remove the 2 screws securing the old element, pull it out, and discard. Connect the new element prongs where the old element fit and screw it back in place. This is a very simple repair that anyone can do.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Little to no heat when broiling
  • See more...

Installation Instructions

Werkheiser from Saylorsburg, PA
Bake element broke
Extremely easy. I unscrewed two screws and pulled out old element and plugged in the new one. Pushed back in and screwed the screws back in. That's it Read more...
Watch the install video
Long Oven Sensor – Part Number: 12001656
Long Oven Sensor
$41.83
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX1570174
Manufacturer Part Number
12001656
This is a factory-certified oven sensor kit with two harness adapters. Its purpose is to sense the temperature inside the oven. Replacing this part can fix an oven that is not reaching the proper temperature (too hot or not hot enough), not heating evenly, or an oven that will not start. To access this part, you will need access to the back of the range. Use a Phillips screwdriver to remove the screws on the access panel. Once the access panel is removed, you will notice a hole on the right side of the oven where the temperature sensor comes out of the oven. You will need to unplug the wire harness, and then open the oven door, locate it in the upper left corner, and remove the screws holding the temperature sensor in place. Pull the sensor out of the back of the oven, and replace it with your new part.
Fixes these symptoms
  • Door won’t open after self cleaning cycle
  • Element will not heat
  • Little to no heat when baking
  • See more...

Installation Instructions

Michael from Pearl River, NY
Oven did not heat up
Removed the oven door, removed existing screws. Pulled wire carefully out of opening, unclip connection. Reattached connection screwed back new sensor attached oven door finished. Read more...
Watch the install video
Bake Element – Part Number: W10779716
Bake Element
$50.23
In Stock
★★★★★
★★★★★
8 Reviews
Fix Number
FIX11703285
Manufacturer Part Number
W10779716
This authentic OEM bake element is square in shape with the terminals in the center and sits at the bottom of your oven. The purpose of this part is to heat your oven in order to cook your food. If your oven is not coming up to temperature, has hot spots, or will not heat up at all, you may need to replace the bake element. To complete this repair, you will need to disconnect the power to the appliance along with pulling it out far enough to access the back panel. Please note that the new element may look different from the original part in your range, but the replacement part will work with your model.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Little to no heat when broiling
  • See more...

Installation Instructions

Jefffrey from EATON, OH
Element stopped working
Disconnected power, removed oven pan that covered element, took off back panel of stove that covered the wiring, disconnected the wires, unscrewed bracket in oven. Removed element then did everything in reverse order. Read more...
Watch the install video
Drip Bowl - 6 Inch – Part Number: WPW10196406
Drip Bowl - 6 Inch
$10.46
In Stock
★★★★★
★★★★★
4 Reviews
Fix Number
FIX11750108
Manufacturer Part Number
WPW10196406
This chrome drip bowl is an OEM approved replacement part designed for use with various models of electric ranges and cooktops. This drip bowl fits under 6-inch burner elements and has a diameter of approximately 8 inches. It sits under the burner, keeping any drips and spill contained. It is common for this part to become discolored, corroded, or otherwise damaged with time, and will need to be replaced. Each drip bowl is sold individually, so this is a good time to check the other drip bowls on the appliance in case you would like to replace those as well (sold separately). No tools are required for installation, simply line up the hole on the bowl with the terminal block and drop it into place. By routinely cleaning this part, it will help to prolong its life.
Fixes these symptoms

Installation Instructions

Henry from St Louis, MO
Replace old drip Bowls
Remove heating elements, remove old drip bowl, install new drip bowls replace heating elements. Read more...
Watch the install video
Drip Bowl - 6 Inch – Part Number: W10196406RW
Drip Bowl - 6 Inch
$14.61
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX2366565
Manufacturer Part Number
W10196406RW
The drip bowl is used for electric ranges or cooktops with the coiled style burners, to catch any drips, spills, or crumbs that may occur while cooking. If your bowls have become discolored, corroded, difficult to clean, or otherwise damaged it may be time to replace them. This repair is easy and does not require any tools to complete the job. Ensure that all burners are turned off and cool to the touch before starting. First you need to lift up and disconnect the burner from the socket. While you have the burner out, it is a good time to check it for any signs of damage. Look at the terminals for any signs of arcing or burning. If you notice this, you will want to replace both the element and the receptacle it plugs into. Remove the old drip bowl by pulling it out. Then insert the new one by lining up the small hole on the side with the element block. Ensure that it is siting flat and then plug the element back into the socket. Please note that the manufacturer has substituted this part, and it no longer has a solid bottom. It is not recommended to cover the hole with products like aluminum foil, as it can trap heat or melt, becoming a fire hazard. As it is an OEM part, it ensures it will fit your model. The drip bowls are sold individually, chrome in color and about 8 inches in diameter, made to fit under a 6 inch burner element.
Fixes these symptoms

Installation Instructions

chris from ABERDEEN, SD
Burner would not heat up and the cook top on light would not turn off.
First turn off breaker. Pull out stove and unplug. There was about 8 screws on the panel on the back side of the control panel. Remove panel. Remove knob on the bad control and there is 2 screws behind knob. Remove those 2 screws and take the new control and remove 1 wire at a time from old switch to new one then put back together. Read more...

Admiral Range Appliance Types

Related Admiral Range Parts

Popular Admiral Range Models

View More
+