Amana Dryer Elements and Burners

★★★★★

★★★★★

10 Reviews

Fix Number

FIX334313

Manufacturer Part Number

279838

Sourced directly from the manufacturer, this heating element is an OEM approved replacement part for a variety of dryers and is sold individually. It measures approximately 10.5 inches long, 7.5 inches wide and 2 inches deep. The heating element is the primary source of heat used to dry the clothes in your dryer. This heating element is strung with a coiled wire made of a nickel and chrome alloy. It may need to be replaced if your dryer does not produce heat, if it produces too much heat, or if it will not turn on. If your dryer does not heat, first check for a blown thermal fuse on the blower housing before replacing the heating element. In most cases, the heating element will have a break in the element, making it defective. For this repair you will need a quarter inch nut driver and a pair of needle nose pliers. Start this repair by disconnecting the power and then remove the dryer vent. This repair is done from the back of the appliance with the back panel removed. With the panel removed, this will give you access to the heater element. Your next step is to remove the high-limit thermostat from the housing and remove the two wires from the heater terminals. Now remove the screws securing the element to the housing and slide the element out. Installation of the new part is done in the reverse order.

★★★★★

★★★★★

4 Reviews

Fix Number

FIX11741416

Manufacturer Part Number

WP3387747

When connected to electricity the dryer heating element glows red hot and generates heat. When air is blown over it, it heats the air which is used to dry the clothes. The heating element fits inside the heater housing inside the dryer. Wear and tear on the heater coil from use will eventually cause the coil to break and the element to fail. When this part fails it can cease to produce any heat. Alternately, the coil could break and short to ground allowing the dryer to continue to heat even when turned off. The latter is a fire hazard and the dryer should be disconnected from power until the element is replaced. If the element coil breaks, the element needs to be replaced. This model is 11 by 5 inches with 5/16” terminals, metal and ceramic, and comes in black. It is sold individually.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX11746337

Manufacturer Part Number

WP8544771

If your dryer is no longer heating up, there may be an issue with the heater element. You are able to test this part with a multimeter to determine if it has failed. If you need to replace the heater element, this is a genuine OEM part. The element has a coiled wire made of a nickel and chrome alloy. The wire heats up due to resisting an electric current, and the heat it produces is then used to dry your laundry. Before beginning this repair, be sure to disconnect the power supply to your dryer, and ensure you have room to access the back panel of the dryer. You will need to disassemble much of your dryer, including removing the drum, in order to access the heater element. The heater housing is found on the bottom right-hand side of your dryer.

Fix Number

FIX4205218

Manufacturer Part Number

DC47-00019A

Includes the insulators and restring already attached. This dryer heating element produces heat to dry clothes in a dryer and is located in the rear end. If the heater element is burned, dryer does not heat or over heats, or clothes take too long to dry, then replacing this part could solve your problem. The tools needed for this repair project are: Phillips screwdriver, putty knife, needle nose pliers. To repair, first remove the main top of dryer and remove ground strap at the rear. Next, disconnect two wire harnesses that hold front panel to the cabinet to pull out front panel. Once you have access to the inside of the dryer, refer to the manual for further installation instruction. As a safety precaution, remember to unplug appliance from power source before beginning this repair project.

Fix Number

FIX334206

Manufacturer Part Number

279457

This heating element connection wire kit is a genuine OEM replacement for your electric dryer. The kit is used to connect the thermostat to the heater element. The kit comes with a yellow wire nut and a wire that measures approximately 5 inches in length. If your dryer is getting little to no heat, or is taking too long to dry, you may need to replace this connection wire. Please be sure to disconnect the power supply to your dryer before replacing this part.

★★★★★

★★★★★

1 Review

Fix Number

FIX4220205

Manufacturer Part Number

DC97-14486A

This genuine OEM heater duct assembly in your dryer directs hot air into the drum during operation. Generally, it can be found behind the drum or at the rear of the dryer. If this assembly becomes damaged, you may encounter problems such as clothes not drying properly or drying unevenly. This kit includes the housing with the heating element coil and attached insulators.

★★★★★

★★★★★

1 Review

Fix Number

FIX2162280

Manufacturer Part Number

LA-1044

★★★★★

★★★★★

1 Review

Fix Number

FIX11741835

Manufacturer Part Number

WP35001247

This element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is used to dry the clothes in your dryer.

Fix Number

FIX11746303

Manufacturer Part Number

WP8541818

The heating element is not included with this box.

Fix Number

FIX11740608

Manufacturer Part Number

WP279843

This element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is used to dry the clothes in your dryer.