OEM Frigidaire Cooktop Parts & Accessories

Watch the install video

CAP

$49.29

Fix Number: FIX11775719
Manufacturer Part Number: 5304508468

Burner Switch Kit

$47.14

Fix Number: FIX470145
Manufacturer Part Number: 5303935086

This switch controls the stove top surface burner.

Fixes these symptoms

Element will not heat
See more...

Watch the install video

CAP

$53.58

Fix Number: FIX11775706
Manufacturer Part Number: 5304508443

Sold individually.

Installation Instructions

Phil from Elkton, OR

8 inch surface element melted at elbow to terminal block - shot out a 6 inch flame.

Note: This is the first time I've ever tried fixing a stove. First, I ordered a new element. Took a minute to install, but it didn't solve the problem. I ordered a terminal block kit and switch kit. Replaced the terminal block. Took about 10 minutes. Only problem was the shrink sleeves melted. Electrician's tape remedied the problem. Tested the element again. It still didn't work. Following instructions provided, replaced the old switch with the new universal switch. First unplugged stove. Removed upper back panel. Took a closeup photo of switch connections, in case I messed up. Removed old switch, leaving all wires connected. Per instructions, mounted new switch and fitted dial to proper length - took about two minutes. Permanently mounted new switch. New switch wire terminals were not in the same location as on the old switch. No matter, both old and new switch terminal designations are clearly marked. Transferred wires from old terminals, one at a time, and connected to corresponding terminal on new switch. Plugged in stove. Turned on the new switch. Element worked fine. Tested the rest of the stove, just to make sure I didn't mess anything up. Everything worked. Replaced back panel. Cleaned up areas on the stove that are hard to reach while stove is in place. Slid stove back in place. Works like a champ. Read more...

Burner Knob - Stainless

$81.17

Fix Number: FIX9495232
Manufacturer Part Number: 318242275

This stainless steel burner knob is approximately 2 1/2” in diameter and is used to control the amount of heat coming from your surface burner element. The knob has off, lo and hi in black lettering. If you are not able to adjust the heat setting for your burner you may need to replace the burner knob, or check the burner switch. This knob accepts a D-shaped shaft, is made of plastic, and sold individually. This is a genuine OEM part.

Watch the install video

Terminal Block Kit

$14.16

Fix Number: FIX470125
Manufacturer Part Number: 5303935058

This kit comes with the necessary components to replace your burner terminal block. It includes interchangeable mounting brackets, a terminal box, ceramic wire nuts, heat shrink protective tubing, and wires. The purpose of this part is to connect the wire harness to the surface element, which allows for the burners to heat up. Some common issues that result from a damaged terminal block is that your element will not heat properly or not heat up at all, may cause burning smell, or make a buzzing noise. If you remove the element and the tips are black, that is a good sign there is a problem with the terminal block and it should be replaced. It may also be necessary to replace the burner elements as well, if the tips are badly damaged. This repair will require a pair of wire strippers, a #1 square head screwdriver, and a heat gun or hair dryer. If you are not comfortable with cutting, stripping, and reconnecting of wires you should contact a qualified professional to complete this repair. Please be sure to disconnect the power supply to your appliance before starting this repair. As this is a genuine OEM parts kit, it will be compatible with your appliance model.

Fixes these symptoms

Element will not heat
Oven not heating evenly
Will Not Start
See more...

Installation Instructions

SHIRLEY O from boxborough, MA

burner would not heat

removed burners, cut wires to each burner, installed new wires from terminal block kit. reinstalled surface element. Followed directions from video located at site of the ordered items Read more...

KNOB

$62.61

Fix Number: FIX16227241
Manufacturer Part Number: 5304525746

This burner control knob offers a straightforward solution for managing heat levels on your gas cooktop. Designed to fit a D-shaped shaft, it includes clearly marked settings such as Off, Lite, and Hi for easy operation. No tools are needed for installation—just pull off the damaged knob and press the new one into place. Whether you're replacing a stripped knob or refreshing the look of your appliance, this part ensures reliable performance and ease of use.

Watch the install video

CAP

$40.71

Fix Number: FIX11775704
Manufacturer Part Number: 5304508441

Sold individually. This part helps the flame to spread for even heat. Also protects your burner head from spills.

SWITCH

$71.11

Fix Number: FIX16227346
Manufacturer Part Number: 5304526190

This replacement infinite switch controls the power flow to cooktop burners, allowing for adjustable heat settings. Rated at 240V and 15A, it fits select electric ranges and cooktops. It resolves issues like burners not turning on, staying at one heat level, or heating inconsistently. Installation requires accessing the control panel and swapping out the faulty switch.

Watch the install video

Left Front Orifice - 9.5K

$32.12

Fix Number: FIX2332664
Manufacturer Part Number: 316527500

This orifice is a replacement fuel-delivery component designed to regulate gas flow to a burner. It plays a critical role in maintaining proper flame size and efficiency and is commonly replaced when flow becomes restricted or uneven.

Watch the install video

CAP

$37.49

Fix Number: FIX11775705
Manufacturer Part Number: 5304508442

Sold individually. This part helps the flame to spread for even heat. Also protects your burner head from spills. The surface burner cap is located on the top of the burner head and is used in ranges and ovens. The burner cap helps spread out the burner flame for even heating, and protects the burner head from cooking spills. Without the cap you can have a burning gas torch. If your cap is missing or is discolored, replacing this part can solve the issue. This part comes in the color black. Remember to unplug your range from the power source and allow surface to cool before installing this part. Refer to the manual provided by the manufacturer for further installation instructions.

Frigidaire Cooktop Parts

Popular Frigidaire Cooktop Parts

Installation Instructions

Installation Instructions

Frigidaire Cooktop Appliance Types

Related Frigidaire Cooktop Parts

Popular Frigidaire Cooktop Models

Frigidaire Cooktop Parts

Start With Your Model Number

Popular Frigidaire Cooktop Parts

Installation Instructions

Installation Instructions

Frigidaire Cooktop Appliance Types

Related Frigidaire Cooktop Parts

Popular Frigidaire Cooktop Models