7MWTW1504DQ0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Found washer to not agitate, washer was making a noise like grinding plastic on metal type noise. Was not sure what was causing noise until finally realizing that agitator was not agitating during wash cycle. To verify concern I removed old agitator assembly and marked top of input shaft and turned
Removed cover from dasher assembly and removed 7/16 bolt, removed agitator assembly and reinstalled new dasher assembly and installed new 7/16 bolt with washer included. Installed cover and tested washer. Washer worked normal again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from NASHUA, NH
- Parts Used:
- WP89503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from BLUE POINT, NY
- Parts Used:
- 63580
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Machine delivered without fabric softener dispenser.
Removed the cover where the dispenser would have been installed and snapped the new one in. 5 minutes. When useing the dispenser after adding softener make sure to fill the dispenser with water to dilute and prevent staining.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from SIOUX FALLS, SD
- Parts Used:
- 63580
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fabric Softner Dispenser severly pluged
Watched the video on this site on removal and installment Done in less than 5 minutes including cleaning where the dispenser is located
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kerry from WALKERTON, IN
- Parts Used:
- WP63235
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
agitator spin freely by hand. plastic splines striped out
remove cap on top of agitator, use socket with extension to remove bolt. pull up to remove old agitator, reverse order to install new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from SAN JOSE, CA
- Parts Used:
- W10404050
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Washer would not adgitate
I ordered a lid switch because the washer wouldn't agitate. Most reviews indicated that was the problem. While waiting for the part to arrive, I discovered the transmission to be of fault.I let parts select know that I no longer needed the part. Parts Select gave me an immediate refund no questions asked and before I returned the part to them. That is customer service!! I will use Parts Select for all my future purchases. I can trust a company that trusts its customers.
Joe M. San Jose
Joe M. San Jose
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from ARVADA, CO
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
out of balance
The info. was really helpful
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tuan from LADSON, SC
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
On Spin cycle washer jumping all over the place.
Just follow the video! Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracy from CONWAY, AR
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My washer was always off balance.
I used a jack to lift the tub and unhooked the rods and replaced them. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from INDIANAPOLIS, IN
- Parts Used:
- WPW10006355
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
would not spin
online videos were great. called to order and lady was very helpful. washer is now operating normal
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from WHITEWATER, CA
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Socket set, Wrench (Adjustable)
Not really a problem but the hardest part was moving the washer to lay on its back.
I simply followed Steve's instructions on video. Very easy repair. Washer works great, no jumping or vibrating.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from LONG BEACH, NY
- Parts Used:
- W10780048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Loud banging during spinning
Followed video provided by Part Select. Video made it look easier than it was but was very thorough and I was able to accomplish repair in less than an hour! The agitator before repair would bounce up and down when I pressed hard and let go. After repair it was much tighter!! Evidently this is a common problem with this design of Whirlpool washers!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from TEXAS CITY, TX
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
machine wobbled violently
followed video instruction that came with part. Previously watched youtube video (there are several, the low production videos are well worth viewing over the professional types). It was a breeze, other than the videos saying one person could do all four. When you get to the last rod, it is more difficult to lift the tub to insert the final rod in the round holder. I asked my wife for assistance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BRISTOL, CT
- Parts Used:
- WPW10006384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Belt needed to be replaced
Took the Cover off and installed belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PINE MOUNTAIN, GA
- Parts Used:
- 8212641RP
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Washer hoses due for replacement
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this instruction helpful to you?
Thank you for voting!