Models > 7MWTW1504DQ0 > Instructions

7MWTW1504DQ0 Whirlpool Washer - Instructions

Jump to:

All Instructions for the 7MWTW1504DQ0
91 - 105 of 117
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Steven from Keenesburg, CO
Parts Used:
W10404050
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
The lid lock switch on our clothes washer went out
I had to remove 3 screws from the back of the washer to be able to lift the top. Then remove 3 screws under the lid which held the switch in, unplug the old part and put the new one in. It was quite sinple. The most difficult part was figuring out you have to slide the top of the washer forward a bit to be able to tilt it up.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Palm Desert, CA
Parts Used:
63580
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Needed fabric softener dispenser.
Ordered the part... snapped it in place.... piece of cake!!! The people at Part Select are phenominal.... best customer service I've seen in years...
Was this instruction helpful to you?
Thank you for voting!
Customer:
Patricia from Berkley, MI
Parts Used:
63580
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
No fabric softener dispenser
Take out cap and replace with new cup
Was this instruction helpful to you?
Thank you for voting!
Customer:
Doris from Faucett, MO
Parts Used:
WP63235
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Would not agitate
Plastic "teeth" at top of agitator were completely worn off, allowing the agitator to spin freely on the shaft. Just remove the bolt that connects the agitator to the drive shaft (located under the top cap of the agitator), remove and replace agitator and you're all set.
Was this instruction helpful to you?
Thank you for voting!
Customer:
joe from Cato, WI
Parts Used:
63580
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
My washer did not come with the fabric softener dispenser
Easy as ONE TWO not even a THREE. Just pulled off the cap on top the agitator and dropped in the dispenser. Gave it a little push to seat it and done. Sure beats the softener ball.
Was this instruction helpful to you?
Thank you for voting!
Customer:
roy from mcdonough, GA
Parts Used:
63580
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
no softener dispenser
Installed cup dispenser and started the laundry
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rennel J from Rosamond, CA
Parts Used:
63580
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Fabric Softener Dispenser won't dispense softerner.
Very easy. Just snapped it on.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from Zephyrhills, FL
Parts Used:
63580
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Softener started dispensing some black gunk . I cleaned the dispenser but could not get all the gunk out. Decided to install a new dispenser.
Pulled off the old dispenser and popped on the new one. As easy as that. No tools needed. By the way. The service at Partselect was unbelievable. Had the part in about four days. Thanks Partselect.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 7MWTW1504DQ0
91 - 105 of 117