7MWTW1604DM0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark from Whitehall, PA
- Parts Used:
- WPW10074580, 285811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
agitator did not turn
I removed the cap over the ratchet mechanism, removed the ut holding the agitator in place, removed the agitator and cleaned all the parts. The assembly for the ratchet dogs was a 3 piece assembly that was included in the kit I bought from Part Select. I also bought a new cap and gasket since my old gasket had broken too. A new gasket was already included in the kit, so I didn't need ot buy the cap. I liked that th ekit included everything I needed and good instructions. parts got to me in about 3 days. Very happy with my Parts Select experience and the fact I saved at least $100.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Danbury, WI
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Top agitator did not work
I removed the cover for the softener dispenser on the top of the agitator. Then reached in and removed the cover of the nut and washer which was very sticky and sealed with an o-ring. This took a bit of pressure. Then used a socket wrench with an extension to loosen the bolt and took the whole agitator out of the machine. Then I set the agitator on the floor and with a fine 12 inch long screw driver released the catches while turning and pulling the agitatior with my other hand and holding the lower agitatior on the floor with my feet. I then turned the upper part over and removed the cogs and holding mechanism.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Jupiter, FL
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Partial Agitation - CAM Agitator teeth worn
1. Removed the fabric softener dispenser
2. Removed Barrier Seal Cover
3. Removed bolt and seal
4. Removed and replaced CAM Agitator Assembly
5. Reversed the removal steps.
2. Removed Barrier Seal Cover
3. Removed bolt and seal
4. Removed and replaced CAM Agitator Assembly
5. Reversed the removal steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dee from SNOHOMISH, WA
- Parts Used:
- WPW10074580, 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Worn out agitator directional clogs.
I just ordered the complete agitator kit since I didn't know for sure what I all needed, and it made my repair so easy replacing since it was all complete. I followed video which was a great help. Got it all done in 25 minutes. Very easy. Thank you...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from S BURLINGTON, VT
- Parts Used:
- WPW10074580, W10772621, 8575076A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Agitator broken. Bolt missing.
Had to clean out area where bolt was to go as it was full of debris. Placed agitator on, bolted on , placed softener dispenser on. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorena from Tampa, FL
- Parts Used:
- 285565
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
the agitator was making loud noises and then the top part stop working
My husband just took the bolt in the middle took the broken one, put the new one, put the bolt back the lid the rubber seal and done. Working like new.
Basically we did what everyone else did with this part, it help me realize I did not need to call a repairman for this, I knew hubby would be able to do this.
Basically we did what everyone else did with this part, it help me realize I did not need to call a repairman for this, I knew hubby would be able to do this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from Rohnert park, CA
- Parts Used:
- 285811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
upper agitator inoperable
Took ten minutes to pop upper assembly off and replace dogs. Note long ratchet or nut diver advisable 5/8.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from LIVONIA, LA
- Parts Used:
- W10404050
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Lid lock not working.
Followed instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucas from ARKANSAS CITY, KS
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Making a loud noise for a while then stopped spinning
Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSE from MILLBURY, MA
- Parts Used:
- WPW10006355
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
washer was draining but no spinning
Disconnect electrical plug from the wall, disconnect drain hoses and tip washer forward remove belt hosing basket and then remove the electrical plug that contains seven wires connected to actuator then remove the two small screws.
Then reverse the operation to stall the new part. Very easy.
Then reverse the operation to stall the new part. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from MENTOR, OH
- Parts Used:
- 285565
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Had to replace the agitator
I already had the old agitator out, so when I got the new one I put it in the tub. You have to spin it a little so it seats properly. I then tightened the bolt with a 7/16” socket and my wife was washing a load within 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from MT STERLING, KY
- Parts Used:
- 8575076A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
fabric softener wasn't dispensing
The old part popped right off, and new one installed. Works Great!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from SILVER CITY, NM
- Parts Used:
- 285811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator dogs broken
Super easy. Watch the video on YouTube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Cudahy, WI
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
agitator rotated in both directions, plastic ratchet had worn out
snapped off the softener dispenser, pulled out the plastic seal below and could see problem. Used socket with extension to remove agitator. ran machine to verify transmission was working.
Looked up parts on line and found Part Select. The repair stories insured me I had correctly identified problem. Ordered part on Sat. arrived Tues. Reversed disassembly process with new agitator. Success
Great source of information, fast delivery, very satisfied overall and will reccomend and use again
Looked up parts on line and found Part Select. The repair stories insured me I had correctly identified problem. Ordered part on Sat. arrived Tues. Reversed disassembly process with new agitator. Success
Great source of information, fast delivery, very satisfied overall and will reccomend and use again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- L from Indianapolis, IN
- Parts Used:
- 8575076A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
purchased w/o fabric softenmer dispenser
take off top on middle section (pops off) pop dispenser on--done
Was this instruction helpful to you?
Thank you for voting!