2DWTW4800YQ1 Whirlpool Washer - Instructions

removed the softner insert, pulled the plastic seal, loosened and removed the 7/16" bolt that holds the paddles in the tube. removed the top part of the paddles/agitators, removesd the old cams and replaced with the new. it works awesome.

Started by replacing the lid latch assembly but this did not fix the problem. Parts Select representative suggested replacing the drive pulley clutch assembly. I order this and a new shift actuator. Had difficulty installing the new black shift actuator as it has a different electrical connection location from the original red part. The plug on the existing wiring harness would not reach the socket on the new black shift actuator. I had to remove the socket from the new black actuator casing so the plug would reach the socket. Washer is now working.

I was emboldened after reading other reviews by how easy it was to replace the agitator in my Whirlpool, with comments like "it took less than an hour". Well, that might be true for some... The video also made it look easy, so I ordered the replacement part. I did not disassemble the machine in advance but I did enough troubleshooting to determine that the clutch was fine, but the agitator failed to spin during operation. When the part arrived I followed the video, but I was unable to loosen the retaining bolt. The failure of the agitator was a result of stripped gear on the inside of the agitator, so it just spun loosely or, during the wash cycle, not at all. Because the gear teeth failed to grip, I was unable to use the agitator to hold the shaft stationary while loosening the attaching bolt. My only option was to cut the plastic agitator away from the shaft using a rotary cutter, being careful not to damage the shaft or the bolt. This was a painful, time consuming job but, with patience, it can be done. Have a shop vac handy because you'll have to stop on numerous occasions to vacuum up plastic pieces and dust, so they don't slip through the small holes in the drum and clog your drain. The problem was compounded because during the initial installation they had used excessive amounts of Loctite and the bolt was glued pretty tightly to the shaft. Anyway, after approx. 4 hours of troubleshooting/repair work the washer is back in operation, and I still saved money on the deal, so I'm a satisfied customer..

I did the repair as specified in the excellent video supplied with the confirmation of my order. It would not have take more than 15 minutes if I had ignored the 13 years of built up scum on all the parts as I disassembled the agitator. Cleaning everything before reassembling took most of the time. It made no sense to me to have the agitator apart without cleaning everything. It works fine now and looks shiny clean.

Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having washer door bang shut.Took longer than expected, but each procedure was simple.

Followed video on your web site, and used that for ways to fix, good directions. If I was more organized it prob would of taken about an hour or less

This washer would not go into spin cycle without going out of balance no matter how we arranged the contents in the drum. We were looking to buy a front loader when I happened open this company with video instructions and positive comments from other people with the same issue. For the cost it was worth a try. Following the video and in less than one hour the washer was back in service. It now operates like the day we installed it new. Highly recommend this fix which should save you hundreds on a new washer.

Popped the old one off and replaced it, piece of cake !

Followed installation video.

1. Removed softner dispenser.
2. Remover plastic cover that protects agitator bolt.
3. Used 3/8 inch drive with 6 inch extension and
7/16 socket to remove agitator bolt.
4. Removed whole agitator assembly.
5. Removed top agitator from bottom agitator. NOTE: This required alot of force due to age of machine.
6. Removed cam assembly.
7. Installed new cam assembly.
8. Reversed steps to re-assemble.
Note: Before I installed the plastic cover for agitator bolt, I cleaned the O-ring and mating surface to ensure a good seal.

Very easy job ....washer works as designed.

Replacing the part was fairly easy. However it did not resolve the problem. The spin cycle did not activate,leaving my washer full of water. We ordered another Maytag Washer. Hopefully this one doesn't break down for a long time.

Removed agitator. (nut under softener dispenser) that pulled top of agitator off and removed and replaced Cog assembly. Reinstalled agitator.

Watched the PartSelect video and it was a help, but it stated to throw away the old bolt and install the new, but it wasn't inclued in the Cam kit and wasn't told when ordering that it should be replaced. Still don't understand why. Took the opportunity to REALLY clean the agitator inside and out of soap scum. Just about soaked off with Scrubbing Bubbles in the shower! PartSelect had the parts we needed at a much less cost than the major stores. Thank you!S

Replaced upper agitator cam kit assembly, very easy to replace and in about 15 minutes. I would also like to mention about PartSelect's web sit is very easy to find your parts and at good prices they even have video's if you need a little explanation on how to install your part.

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.