LAT7800ABX Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Helenville, WI
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
no hot water
very well . it was very easy 20 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Commerce Township, MI
- Parts Used:
- 205613
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Valve did let cold water run into washer
Removed two screws , two more on the valve, loosened the hose clamp. Reassembled the same way
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald D. from Miami, FL
- Parts Used:
- WP22001448, 206638
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
on spin we notice water from the bottom(underneath)the washing machine.
I did it per the video on line and was a snap.I don't have issue recomending the web site to my freinds who want to do repairs themselves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sonya from Arlington, VA
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
no cold water for wash cycle as if there was a flow restriction
Ordered replacement water inlet valve, switched out within 10 mins and problem solved for less than $50. Maytag design easily allowed for the inlet valve unit to be replaced without accessing interior workings of the washer. The unit is mounted with 3 screws on a removable rear panel where the hot and cold H2O hoses are connected. Very easy! Tested immediately upon completion and was delighted to see that hot, warm and cold water filled the tub extremely fast, the way it worked when purchased new 18 years ago. The web site repair video was key to my success.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jon from hartford city, IN
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
mixing valve cold water solenoid not working. Cold water wasn't filling.
Shut off hot and cold water supply and removed hoses from mixing valve. I unplugged the machine and removed the screw holding the plate that the valve is connected to. I removed the plate and valve and used my smart phone camera to photograph the wiring connections. The next step included removing the wires, the hose and clamp. Remove the valve from the plate. Reverse the procedure for installation. Make sure that the valve and plate are adjusted as far from the drum to prevent contact when the machine is going through spin cycles. The procedure took about 10 minutes and fixed the problem. You have to love Maytag for their reliability and ease of maintenance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Byron from Old Tappan, NJ
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
When warm water was specified, the washer leaked
My nephew followed directions in the repair video. Washer no longer leaks when warm water is specified.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Villa Hillls, KY
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Erratic Fills
Studied, diagnosed the issue, looked at symptoms described in ParrtSelect's on line resources, purchased the part. Had it in one day without the need for extra FedEx shipping charges; waspleasantly surprised to see how easy this repair was to make. I then replaced inlet hoses with new stainless steel types. This workhorse pair of of Maytag appliances, constructed in January 1985 will continue to serve for many more years. These are well-built battleships! And PartSelect will be my part source of choice to keep them going!
Was this instruction helpful to you?
Thank you for voting!
very low inlet volume / low pressure
Removed fill hoses, inlet valve cover,valve mounting hardware,hose to tub,unplugged electrical connector.Installed new valve in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- april from independence, CA
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
water leaked from the cold water inlet. Must have been stripped. I just acquired the washer.
With the help of my 3 year old grandson, we removed the inlet hoses and inlet panel. The water inlet valve replacement was a perfect fit. All connections conformed to the original part. I had reviewed a video at the time of order, so was familiar with the process by the time the part arrived. The website was very helpful in determination of what was needed to fix the washer problem. Shipping was fast and tracking the package provided my schedule. I will utilize this site in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Cotopaxi, CO
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Cold water would not shut off
Pulled the washer away from wall and tipped forward, leaning against a chair. Removed the hot and cold water hoses. Removed 1 screw. Pulled the plate off the back of the washer. Removed two screws holding the old valve onto that plate. Took 4 wires off the original valve one at a time and placed the wires one at a time on the new valve, so I didnt have to write down or remember which wire went where. Slid one hose clamp up, pushed the hose off the old valve and placed it on the new valve. Threw the two screws back on the valve and fastened it to the plate. Put the plate back on the back side of the washer with one screw. Put some teflon tape on the threads of the new water valve and screwed on the hot and cold water hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- R from ALTHA, FL
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
washer kept filling up
I didn't expect a problem, but watched the video anyway, it was right on the money. Make sure to use a new clamp for the hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arcie from Plumas Lake, CA
- Parts Used:
- WPW10116738
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
broken siphon elbo
Had to remove front of washer to get to the back of the washer to make repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Westbrook, CT
- Parts Used:
- 205613
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
bought unit used! Former owner cross threaded the inlet valve -wonder it didn;t leak before now.
pulled out wash/dry stacked combo unit from cubbyhole (this was the hardest part) . Shutoff both hose supplies, turn off power to unit.disconnect power cord @ coupling. Disconnect both hoses @ machine and drain into pan. Remove old valve assembly,take note of what wires go where and disconnect. Remove filler hose from valve. Install new unit in reverse order but using new hose washers and be carefull not to cross thread the plastic threads and only tighten as much as needed to keep from leaking. Have bought from these people before and they are SUPER. Had the correct part in LESS than 24 hrs. and for a reasonable price !! Sam
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Beavercreek, OH
- Parts Used:
- 205613
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water leaks into wash tub when machine is not in use
Unplugged AC cord. Removed hot and cold supply hoses. Removed front cover (2 Phillips screws near bottom). Raised lid, and removed fastening screw for injector tube. Removed retaining screws for inlet valve mounting plate. Positioned mounting plate partially inside rear of machine and removed (4) wires for solenoid connections. Re-positioned mounting plate slightly outside machine and removed valve mounting screws and old valve. Attached new valve (no modification to valve needed for my machine), and worked backwards through the steps listed above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- luis from riverside, CA
- Parts Used:
- 205613
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
water flow would not stop
just like the vidio, only a had to remove the back panel to replace the valve. but we ., or should say my mother has a working wacher now,thank you for your help,
Was this instruction helpful to you?
Thank you for voting!