LAT7800ABX Maytag Washer - Instructions

Took off front washer panel push drum to one side reached in took out four screws on back of washer removed siphon break from ebow for drain hose pulled siphon break to front of washer cut hose clamp installed new part reversed procedure to put washer together Tested operation worked fine no leaks no water on floor wife very pleased with fix Thanks again for fast delivery and great inventory of parts

First I remove the hot & cold water hoses using an adjustable wrench. I then unscrew the panel that holds the water inlet valve using a nut driver. I then carefully pull out the panel, moving the harness wires out of the way, so that I can loosen the clamp holding the inside rubber tube. I remove the old water inlet valve from the panel by removing the 2 screws and then put the new one in. I then reconnect the rubber tube and tighten the clamp. I then screw back the panel and reconnect the hot & cold water hoses. It took me about 20 mins to complete the job.

Removed old part, installed new part. tested machine. worked fine.

I found that the water was coming from top of syphon break. Took it out located it on computor , ordered part. Took about 10 min to replace. EASY

First thing unpluged power cord from wall outlet, removed hot and cold water supply hoses.Then took out srew holding metal plate ,pulled plate out exposing valve, marked wires and diconnected.Pulled clamp and hose from valve.Pulled out valve and reinstalled new.Reconnected wires and hose.Installed screw to hold in place, reconnected hot and cold supply hoses.Plug unit back in. Job done.Washer works like new.

First removed 2 screws(phillips) at bottom of front cover and lifted front to remove. Then removed 2 3/8 screws from under top cover and lifted cover and slid forward to exposed Syphon Break. After running briefly on spin, it was easy to see where the leak was. Syphon break was installed in 5 minutes by removing both hoses and 4 hex screws and reinstalling. Part arrived as promised in 3 days. I was very pleased with the whole experience.

Remove the following items: Washer to sink hose (loosen hose clamp and twist hose), two philips screws from bottom of front panel, front panel, upper side bolt screws, tilt up top washer deck and secure, remove 4 syphon break screws from rear of unit, remove pump to syphon break hose,
remove old syphon break, install new part and tighten with hose clamp, re-install pump to syphon break hose, re-assemble in reverse order. Check for leaks. Show your wife.

followed simple directions... no brainer.
just be careful - shut off water and unlug first.

Install new siphon break connector: 1. Loosened the clamp holding the drain hose in place on the elbow at the rear of the washer. Removed the hose from the elbow. 2. Removed the round upper access plate on the rear of the washer. 3. Removed the 4 screws holding the elbow in place, thereby releasing the siphon break connector and internal drain hose inside the washer cabinet. 4. Reached through the access port, grasped the siphon break connector end of the internal drain hose, pulled it through the access port. 5. Loosened and removed the clamp on hose, then removed the old siphon break connector from the end of the hose. 6. Installed the new siphon break connector onto the hose, clamped it in place, then returned the hose into the washer cabinet through the access port and positioned it onto the elbow, tightened the part down by reinstalling 4 screws at elbow on rear of the washer and then reconnected/clamped the external drain hose onto the elbow and replaced the access port cover.

Just as the video described.... Unplugged the machine, turned off the water, both hot and cold. Unhooked the hoses (replaced them at this time since they were over 5 years old). Took out the top screw holding the frame piece and removed from machine. Took off the wires and the output hose. Removed the valve ass'y from the frame piece. Matched new to the original and reassembled in reverse order.

Went on line an watch video that described the problem. Order the part and received it overnight. Went back online to your website and watched the video on how to do the repair. Followed the suggestions in the video and finished the repair in about 30 minutes. Really appreciate the help your company give me and have bookmarked your site for future use.

very simple to repair, three screws and disconnecting water supply pulling four wires then reverse steps and done, time spent less than 15 minutes.

My husband figured out what the problem was and I looked for the part. It was easy to find on your web-site, and the picture was spot on! I ordered it and had the part in 2 days. The repair took 15 minutes or less, and my washer is as good as new. Thank you PartSelect for being there when we needed. I will recommend this to everyone.

Very easy as the water inlet valve is located on the back of the washer and it was a simple matter of shutting off the water, undoing water hoses, undoing water inlet valve which didn't even need to remove the back side of the washer and connecting the new part, water hoses and turning water back on. The hardest part was tipping the washer, my sits on top of the cold air return, and balancing on a milk crate. Very pleased with being able to do my own repair.

Because the washer was old, 27 years, I actually ordered a new machine but after doing so was able to get the old washer to pump out the water. It had overfilled and spilled water on the floor. The next time I ran the washer using "warm" setting the hot water inlet solenoid failure was evident. I checked voltage at the solenoid and it was getting power so figured I'd try ordering a $30 part. In a couple of days it showed up and after less than :30 minutes I had the washer running again. It would have taken less time but a screw stripped out and I had to locate a replacement. I'd definitely recommend PartSelect. Oh, we cancelled the replacement washer and figured the Maytag repairman could resume his slumber!