SAV5710AWW Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jim from Courtland, VA
- Parts Used:
- 205217P
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Leak from seal on pump
This washer was "professionally" repaired six months ago....that being said, I found two of the three Torx screws holding the pump to the motor to be lying inside the cabinet. This allowed the pump to move and wallow out the seal. Replaced the pump and replaced the screws correctly. No leaks, no problems. Pump is an exact replacement from PartSelect and ease of installation was no problem. Would suggest if you are going to replace the pump, order the three screws and replace them too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from Aloha, OR
- Parts Used:
- WP27001113
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Timer was sticking on rinse
The person who wrote in on how he did his repair on the timer was perfect. I would have replaced the time on my own but I would have taken longer. Instead, I followed his instructions and finished in a little over 15 minutes.I like how you print people's instructions. It definetly helps the next person. I also like your set as well Tks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Pembroke Pines, FL
- Parts Used:
- R0131578
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
hotwater was coming out slow to fill the was tub of machine
removed both hot and cold fill lines and front of washer panel. removed screw holding mix valve plate t the back of the washer . Unpluged connections to mix valve and replaced valve. ( note removing the top of the washer is needed and can only be done by first removing the front by sliding a thin screw driver between the top and front panel to release the clips at the ends.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Virginia Beach, VA
- Parts Used:
- R0131578
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Could not get adequate amount of cold water
Replaced the mixing value using the kit purchased from PartSelect. The instructions with the kit plus the installation tips found on their WEB Page were extremely helpful. Everything went as predicted except I had to cut and insert a new piece of wire on the white wire between the hot and cold electrical connections. I used two crimp connectors to lengthen the wire. This was a very simple job for a 73 year old man like me. Thank you for the tips and quick delivery of the mixer value kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Bel Air, MD
- Parts Used:
- WPW10121334
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Clanging of dryer when rolling
Followed video on PartsSelect website, they made it real easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lizandra from Roxbury, MA
- Parts Used:
- 205217P
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Washer pump was leaking water
Removed spring, then hoses and then belts. When all was removed we loosen the old washer pump and installed the new pump. Everything was re-installed and was put to wash. At first it leaked water that was already sitting there, but then it work like new. Oh I also read the instruction on this website, I recommend the site to everyone!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from Florence, KY
- Parts Used:
- WP27001113
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Washer would not finish washing even though the timer was done. Did that for a weel or so then finally quit.
Washer was full of water when it finally quit so I had to remove the front panels first so I could manuver the top to get to the back of the control panel. Remove the five screws from the back of the control panel. Pop off the cover on the timer knob. Pull the button from the center of the knob once the cover is off . Remove knob. Inside the control panel there is one screw holding the timer in place remove that and slide timer towards the center of machine ,remove electrical connector and it should be out.And remember to unplug machine first!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Swanton, OH
- Parts Used:
- WP40094201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Water leak
Removed old hose by sqeezing clamps and sliding off of fittings. Placed clamps on new hose. Slid hose on fittings. Repositioned clamps over end of hose. Job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Destrehan, LA
- Parts Used:
- WP27001113
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
machine wouls not cycle
Took 3 different tools to take plate oof. Phillips head on top, flat head on bottom and nut driver for the timer.7 screws, 3 tools!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney from Satanta, KS
- Parts Used:
- WP27001113
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
would mot go from one setting to next
pulled washer out and unpluged it removed 6 screw removed old timer and put in new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Andover, NH
- Parts Used:
- W10116791
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Tub leaking and bearing very noisy
After totally disassembling the washer ; the parts arrived, wrong parts! called and resolved issue, recvd parts and proceeded without special tools, PB Blaster solvent is awesome!!! I removed the seal & bearing with little effort with a hammer and screw driver. Greased new seal and installed effortless. Waher back in operation in less than 2 hours of receiving the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Homestead, FL
- Parts Used:
- 205217P
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washing Machine was leaking.
First, I removed the screws, then removed the pump. I, then, installed a new pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Euless, TX
- Parts Used:
- 205217P
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
washing machine pump repair
I ordered my part on Monday. It was delivered on Tuesday, and by four o'clock we were in business. I highly reccomend PartSelect.
Was this instruction helpful to you?
Thank you for voting!
pump leaked, water valve didn't have cold water
disconnected valve replaced with new, real easy. I removed motor and belt ,4 bolts, than removed 3 star screws from pump, replaced pump and replaced unit. Worked great!!!
Delivery of parts was faster than promised, standard shipping.
Delivery of parts was faster than promised, standard shipping.
Was this instruction helpful to you?
Thank you for voting!