SAV5710AWW Maytag Washer - Instructions

Removed upper back panel.(3 screws) Unplugged washer and remove timer. Unplug timer from wires. Replaced timer and reinstalled.

It was so simple I don't think I even need to explain. Couple of screws in and out and done. Saved big money by doing the repair myself...I was surprised how quickly the part arrived. I was able to access from the back of my machine. Did not have to remove the top. Very easy thanks

Pushed new knob onto shaft

took the belt out and took the thing out and fixed then put it back.

1. unplug unit 2. remove front access plate 3. disconnect tension spring on drive belt 4. remove 4 motor mount screws 5. disconnect intake and return lines from pump using a pliers to decompress compression rings and sliding lines off. 6. Manipulate motor and loosen drive belt from bottom of tub and let it hang. 7. tilt motor bottom out exposing pump and remove 3 screws using TREX head driver and remove pump. 8. install new pump

I just removed the screws on the back of the control panel. There was one 1/4 head screw holding the timer in place. I removed that and slid the unit to the right. I removed the connection module. Then I popped the connector on the new unit and slid it back in and bolted it back in. I had to remove the face of the dial on the front and slide the dial off the old unit onto the new timer. This was a very doable do it yourself job.

I removed the lower front panel to diagnose the problem. After finding this, it would have been best to purchase the parts because the instructions on how to disassemble the unit came with the parts. Sad to say, I didn't tighten the main hub, at the bottom of the unit, good enough because it came loose and I had to go back and do a better job. Luckily I was able to fabricate the tool to tighten it better. Too bad the web page didn't recommend the right tools for the job. I would have purchased them.
All in all the job went well. I am pleased with the parts and prints available to complete the job. I could have used some instructions before removal of the parts, but where would be the adventure in that, right?

Rivman,
Milwaukee, WI.
12/2009

Remove the lower access door in the front of the machine. Then I tipped the washer back against the wall to access everything. The pads are alittle hard to push in between the washer pulley disc. So I first pushed in an old broken brake pad off to the side, then was able to push in the new pads. The rear pad is the hardest and I had to release some of the front tub springs and remove the pump hose for access. Overall it went pretty smooth. Thanks for your help!Tim

Part received was correct (5 days ARO). Removed motor assy from unit (left wires connected). Found drive belt was also worn out & obtained a new one locally. Seperated old pump from rusted motor shaft using 2 screwdrivers. Had to use a file to lightly "polish" rust off motor shaft to install new pump. On-line parts diagram helpful in getting belt properly alinged to idler pully. Machine now runs smoothly, dosn't leak and sound like new. Wife happy (me too)!

I unplug the power plug, turned off water supply and unsrewed the water lines connected to the clogged valve.I unsrewed six screws on the front of the washing machine and took the front panals off. lifted the the washing top and replace the hose and intake valve, which was shipped to me. put the top down and put the two front panals. reconnected the water supply to the new valve and turned the water back on. connected the electric plug.works as good as new.

Very easy repair. Removed the lower front panel of the washing machine (two screws) with nutdriver.

Removed hose clamp with pliers. Removed hose from machine. Replaced hose and ran thru a full cycle to check for leaks.

No leaks, back in business in under an hour. This time includes going out to garage and gather the two tools needed for the job and cleaning up the water that came out of the hose during the removal process.

First removed all screws with a nutdriver then lifted the body from the base. Removed the two hoses at the pump (be ready for excess water). Removed the 9/16 bolts (4) to drop the motor assy. I also took off the two front balance springs to have easy access. I at this point was able to remove the pulley and put new belt & pump on the motor. Remember to watch carefully to align belt. removing the idler pulley is a no brainer. Took about 45mins. to complete, a no pro job!!

MAYTAG SAV2655AWW Series 10 Washer Tub Bearing and Seal Replacement

1. Unplug washer power cord and turn off water supply to hoses.

2. Remove lower front panel, 2 5/16” hex head screws at bottom of panel.

3. Remove front upper panel, 2 5/16” hex head screws at bottom corners of panel.
4. Slide washer out from wall far enough to provide clearance to lift washer top panel and control head.

5. Remove 2 5/16” hex head screws securing washer lid panel to side panels and lift lid.

6. Pull fabric softener dispenser from agitator, pulls off easily.

7.Remove agitator upper section, pulls off easily. Remove ½” hex head retainer bolt from inside agitator.

8.Remove agitator base section, pops up, place fingers under each side and pull up gently.

9. Remove tub top ring by pushing down at each clip and then prying out lightly to disengage clip, 8 total. Orientation for reassembly is done by referencing the double tabbed clip on the right side of the outer tub.

10. Remove inner tub retainer bolts, 4, ½” hex head. Clean off mounting hub to expose 4 pry slots located exactly opposite each other. Using wide flat head screw driver carefully and evenly pry up inner tub off of aluminum mounting hub. Once tub is ¼” or more raised a wider blade pry bar will help prevent cracking or breaking the inner tub.

11. Remove plastic seal cup from transmission shaft by turning it counter clockwise with a medium to large pair of water pump pliers.

12. Remove inner tub aluminum mounting hub by using a hammer and broad flat faced punch or drift and driving the hub counterclockwise. You can be aggressive about this as kit comes with a new hub. It will loosen at some point and can be unscrewed by hand. The transmission shaft threaded section must be thoroughly cleaned to remove all sealers or debris from the threads or the new hub in the kit will not thread on correctly and will be excessively tight. Lightly place anti-seize lubricant on the threads before putting on new hub and seal cup.

13. Remove water pump hose from outer tub. Then remove second hose from water pump.

14. Remove “Fill Sensor” hose. Back left quadrant of outer tub, pulls off easily.

15. Remove 6 tub ( 3 pairs) stabilizer springs, plus 1 spring in very back. Try to watch how back one connects to tub mount. If you miss it hooking it back up is pretty straight forward. Only secures one way. Channel locks or vise grips work best for working with springs.

16. Disconnect wire harness from motor drive assembly and tub frame mount.

17. Pull tub and motor drive assembly out of washer cabinet. Lift carefully by shaft and tub mount frame.

18. Remove 6 outer tub retainer bolts and 2 upper motor frame bolts.

19. Lift tub off motor frame and set on its side carefully to prevent damage to “Fill Sensor” back left side.Use a slide tool to pop bearing assembly out of tub bottom.

20. Clean the tub, bearing mount surface, remove all grease from shaft and shaft spline sealing O-ring.

21. Wet new bearing seating surface and tub mounting surface lightly with water and press in new bearing by hand.

22. Clean both inner and outer tubs inside and out thoroughly. Clean hub mounting threads on motor shaft thoroughly.
There can be no residue of any kind in those threads or new hub will be difficult to impossible to screw on without damaging it.

23. Reverse dis-assembly procedure to reassemble machine. Recommend replacing drive belt and idler pulley if found to be excessively worn or damaged. If brake assembly is heavily worn or pads are cracked this is the time to replace those as well.

Removed broken piece and put on new part.

Ipulled the front panel off and found that the brake pads had broken into pieces, ordered new pads. Two of the pads were accessed from the front of the machine and were relatively easy to replace by removing the two attaching bolts, spreading gap in area that they fit into with a plastic pry tool. I gained access to the third pad by removing the punch-outs on the side of the machine (circular). If I had not had these prepuched pieces available to me I would have simply cut an access hole in the rear of the machine with a jig saw, (who will ever see it).