MAT12CSDGW Maytag Washer - Instructions

Removed access panel on back of machine to remove Air Tube where it connects to wash basin. Removed control panel cover on top of machine and front panel of machine so top could be lifted for easier access to the point where Air Tube plugs in to water level selector switch. Tube is attached at both ends via spring clips. Replaced tube; problem solved. As a note, the old tube was clogged, and once cleaned, the machine functioned normally again. I had already ordered the replacement so I installed it in place of the old tube when it arrived. The new tube is significantly longer but functions perfectly.

even though i could have have ordered the spring that broke i took the easy way out and ordered the assembly it took less than 15 minutes to get done, and now the wife is happy and now i'm happy too.

Purchased x4 new adjustable legs. Leaned the washer back and held in place with block of wood. Loosened the two older front legs with an adjustable wrench because they had a locking nut and replaced with new legs. Repeated process on back side of washer. Once all the new legs were installed leveled the machine adjusting the legs if necessary.

I wached the six min. Video you sent me,so helpful what a great idea so the job only took me about five min. Thanks Mike

I took the front panel off and was able to easily access and remove the leaking drain pump. Then I propped the front of the washer up onto some boards so that I could put the two pulleys back onto the new pump, then I just tightened the three bolts in order to tighten the pulleys. However,when I started another load of wash there was a leak in the bottom of the tub, so I removed the new pump and went out and bought a new washer, figuring that our 13-year-old Maytag was going to cost more to fix than to buy a new washer. Then I wrapped up the new pump and sent it back. Thanks for all your help and for letting me send back the new part...I received confirmation of my refund today. Bob Trautman

Pump was eazy to replace the clean up took longer than the fix.

Moved washer away from wall. Removed rear panel (4 screws). removed hose bracket (1 screw). use vicegrip to "open" hose spring clamp. Removed old hose, slipped spring hose clamp over new hose. "Opened" spring hose clamp put new hose over washer drain, released vicegrip. Assemble in reverse.

I watched a utube video showing how to do the job. It was simple considering I am not mechanically gifted. The whole job took about 20 minutes. The hardest part of the job was moving the dryer out of the way first.

I removed 2 Philips head screws from bottom of front cover and removed cover. Tilted washer back and installed a 6' wooden block under washer. removed 3 hex head screws from pump base using my flex shaft nut driver and a 5/16" socket. Removed the 2 hose clamps from pump and lifted pump out. Pump appeared to be ok but checking by turning the pulley I found the impeller did not turn, shaft key must be sheared. The new pump came the next day at 2:00 PM and it was an exact replacement. Installed and up and running in about 15 min. Working fine.

Once i figured out it would not drain i pulled the front panel off and pulled all the drain hoses off to be sure nothing was clogged there or in the pump itself. It was not so then i checked the drive belt and it was ok. Next i pulled off the drain pump and everything looked to be ok, it was not froze up and it would spin just fine. I got a screwdriver and held the splines inside the pump while trying to turn the pulley and thats when i found that the propeller was spinning on the shaft and under a load would only spin the shaft and not the propeller inside the pump. Got online ordered new pump and it works great now.

Got ipad and follow direccions on utube.

The water pulley wheel kept seperating from the pulley shaft after numberous attempts with plumbers glue, the problem kept repeating therefor replacement was necessary. After ordering the part it was able to be replaced with the new pump and fast, washer running like new. Thank you so much.

unpluged washer pulled away from wall. removed control panel rear plate. removed control panel mount screws n dislocated control panel. removed lid switch and noticed that the metal tab that activates switch was bent out of place. adjusted metal tab for proper switch action. installed a new switch just to avoid future problems and reinstalled everything. ran operational test.

1. Removed the front panel from the washing machine. This entailed removing two phillips head screws on the bottom left and right of the panel. Then, I pulled the bottom of the panel out and up until the top of the panel was disengaged from the machine. 2. Noted the belt tension on the old pump so I could install the new one correctly with the same tension. 3. Removed the two hoses from the pump, and the three screws securing the pump to the washer. 4. Installed the new pump providing the belt the same tension as I observed on the old pump. 5. Installed the hoses and tightened the hose clamps. 6. Reistalled the front panel and ran the washer. Works fine!

Emptied washing machine tub with a small plastic bowl into a 5 gallon bucket, finihsing up last bit of water by soaking it up with towels. I next removed front panel on washing machine by unscrewing two screws on the bottom front, left and right, to gain access to the pump. Loosened two hose clamps and detached two hoses, catching remining water from washertub. moved washer out from wall about 3 feet and tilted washer back towards wall so I could access the inderneath of washer to lossen three bolts that held pump in place. removed belt from pum to motor and examined fro glaze or wear (none detected) and then removed pum and reversed steps to install new pump, reinstalling belt faily loosly, per instructions. Tried washer to see if ssue resolved and once confirmed, replaced the front panel. Have done multiple washes since then (at least 10) and no further issues. Very economical solution (under $100) and sense of pride with fixing applianmce myself. This web page was very informative and saved me a lot of money and time. Thanks!