LAT7300AGX Maytag Washer - Instructions

First I unplugged the power cord from the wall. Then I turned off the water supply shut-offs at the wall and removed the hot & cold connections at the rear of the washer. Then I removed the two screws that held the assembly in the rear of the washer. I then pulled the assembly out about 3-inches, marked the new assembly to show the proper color of wire for each lug and disconnected the four wires at the lugs. I disconnected the rubber fill hose from the assembly and removed the assembly. Next, I installed the new assembly in the reverse order. It worked fine without any leaks & saved me from buying a new washer. My old washer now gets my clothes cleaner than it has for years - much quieter and quicker too.

The repair itself is fairly simple. However, being 65 years old getting the new valve back into the back opening of the washer and screwed in was a challenge. The clamp on the water connector hose broke and I had to drive to the store to replace it. You may want to consider giving a heads-ups option of ordering hose clamps to DIYers, when you go to order. Also, the instructions that came with the part was not totally accurate. I had to rotate the cylinders outward to connect to the electrical points. But, my machine is pretty old and that may be why. Otherwise, I am very pleased with how quick I received the part and it was exactly what I ordered. My washing machine is back in business. Thank you

Removed the old hoses and screwed on the new hoses.

well i first put on 2 new belts because they were worn and smoking. the new belts did not fix the problem. you suggested putting in a new pulley. it went against my better judgement that the pulley was defective. well i put in the new pulley and now the real problem has surfaced. the transmission is not working. now i want to order a new tranny and low and behold it is no longer available. well why did you sell me a $99 pulley when that was not the next part to change after the belts were replaced. now i have a new pulley on a washer that is going to the recycle center as metal trash. well on my part i will reward maytag by buying a ge washer now. plus i will not count on using you as my parts supplier.

My Maytag A308 is about 25 yrs old and has been filling by a trickle for a while - both hot and cold. I replaced the water valve and that fixed the hot. Cold still running slow. I switched the hoses, thinking one might be clogged, and determined that the cold shut-off was clogged. I replaced that with a ball-valve - about $10 - and it works like it used to. My advice to anyone who installs a shut-off to any fixture - sink, toilet, w-machine, etc - NOT to use a cheap washer-type valve - they tend to freeze up over time and do not close when needed. Same for clean-out drain on hot water heaters.

Water valve on the A308 was accessible and easy to replace. Required rotation of solenoids was easy and connections were obvious. PartSelect
pictures were very useful and price was better than other on-line sources.

Ron

The replacement of the Water Inlet Valve supplied by PartSelect (model PS60378) was too easy.
The key issue was to remove previously the whole upper cover of the washer machine, including the Control Panel, and disconnect all the cables from the electronic Control Board, in order to work easy and freely to remove the inner water hose that is connected to the water inlet valve, working from inside and not from outside of the machine.
Care must be taken writing a notepad of the position of every cable, for not making mistakes when reconnecting them to the Control Panel.

Read repair stories on website. Removed front & top to find leak, Ordered part. Replaced valve. Had trouble with clamp.It only caught in first slot, then broke. Had to go to hardware for one slightly larger.

I removed the two hoses connected to the valve, then I removed the front panel by removing two screws on the bottom. I disconnected a drum hose connected to the top, tilted the top back, then separated the inlet valve from its metal housing by removing the screws holding it in place. I then removed the metal housing in order to have more access to the old valve. At this point, the valve was only held in place by a few wires. I noted which wires connected where and how the valve was oriented (Hot/Cold position), then removed the wire connections with pliers by grasping the connectors (not the wires). I then reversed this process to install the new valve.

Watched your video and followed your instructions and it was very simple.We bought our maytag washer in 1988 next year it will be 30 years old we raised 3 children and for $21 and your video I hope to it last another 30 years

I watched your 'how to' video, then repeated the procedure on my own machine. The repair went pretty much like the video. The new valve corrected the problem, and in fact, fills the washer faster than the old valve. I also replaced the water supply hoses, as one started to leak after I jiggled it around during the repair. Very satisfied with the this sites experience.

Followed video that came with part.

I order a water inlet valve from this site It was the best buy around. The email from the site part came with a video how to change it. It was a 15 minute job. One 5/16 nut driver to remove the inlet valve and pliers to remove the hoes from the valve. Easy off easy on.

removed cover, disconnected small water tube and disconnected electrical connections. Reversed above to install new piece. two nutdrivers required. Channel locks for supply hoses.

Terrified that the washer water value would blow due to the noise... Diagnosed the problem, ordered the part and it took only 10 minutes to fix. The hardest part was moving the washer in the confined space, which required moving the driver out and sliding the washer at a 45° angle in order to reach the access panel. Once access gained it was straight forward. Step 1 removed fill hoses from supply. Backed the valve assembly out; detached water hose from value assembly with nut driver; detached wires'; value released; added new value and reverse process. Checked for leaks, reassembled fill hoses with new washers (stainless steel hose), ran cycle, checked for leaks, replaced washer in original position Need commend the video producer and repair person in the video. The narrative gave me the confidence that, Yes, I can do this.

Unplug machine and remove drain hose clamp and hose from rear of the machine.Using Phillips head screw driver remove the 2 screws from the lower front panel of washer. Lift and remove front panel. Using a small socket, remove 2 screws from the inside top left and right of machine which secures the machines top cover and lift cover up (use duct tape to secure washer lid from opening). At the inside rear top of the machine is the Siphon Break Connector. Loosen clamps, remove old Siphon Break Connector and install new one. Reinstall top cover, front panel and then drain hose.