LAT7300ABX Maytag Washer - Instructions

I found that the water was coming from top of syphon break. Took it out located it on computor , ordered part. Took about 10 min to replace. EASY

Removed old part, installed new part. tested machine. worked fine.

Removed door panel to get to the electric control conponents and noticed a burned wire to one of the door microswitches. Ordered the door switch repair kit from PartSelect. Also, ordered and replaced the thermal fuse at the same time since it was only $12 and didn't know if that blew at the same time the switch cooked. I had the parts coming standard delivery (3-5 days), but they arrived the very next day. Parts included easy to follow directions.Job went pretty smooth and the dishwasher works again Good experience!

open top of washer
remove two screws that hold water inlet valve
disconnect four wires and hose;replace new water inlet valve and reversed operation
everything went well

The repair was simple, and followed the instructions exactly. Removed three screws, one small hose clamp, and two electrical connectors. Replaced and reassembled. Worked like a champ!

1. Identify washer model and symptom
2. review page of suggested part; view installation video
3. order part with standard shipping
4. receive part next day and install just as the video showed

Entire job from going to PartSelect website to completion took less than 24 hours. Hardest part was moving the washing machine. Machine is nineteen years old and now works perfectly. Unmatched service.

I had taken the washer out and replaced both hoses, and the leak stopped for a load or two. I then replaced the water inlet valve, because I could see that the plastic threads were pretty bad. The repair is very simple on this model. There is no need to open the cabinet at all, the entire job is done on the back. I used a socket and the stubby driver for the mounting screws and switched to a screwdriver tip and opened the clamp on the hose leading to the air gap assembly. The entire operation took about five minutes. The repair worked for two or three loads.

The water leak came back, so after some searching I finally figured out how to open the cabinet, and that took longer than actually doing it. The front opens with two big screws located on the front about 4" above the floor, just in the corner of the indentation on the panel.

With the top tipped up (tape the lid!) out of the way, the leak proved to be coming out of the air gap assembly. There is an injector nozzle and a rubber sleeve that goes over it. They fit in the large black hose. I easily opened the hose clamp, removed the old parts, put in the new one. The rubber sleeve has a cover that goes over the edge of the plastic injection nozzle. You have to make sure it is entirely and smoothly inserted. Easy. Then insert it all the way to the shoulder of the end of the hose with that wide end facing into the hose and the other end open. Slip the open end through the bracket and into the other hose. Tighten all your clamps, and carefully pressure test. Do not touch any metal parts if there is water spewing. Just turn it off, pull the plug, and fix the problem. In my case, it worked perfectly, and I turned it off, replaced the front and the job was done.

Despite the great advice I got here, I ended up getting the nozzle parts in town. I had to go to an appliance parts outlet rather than a place like Home Depot, but it was quick and no shipping. Still, I would not have tried this without the great advice and fast service here.

Took off front washer panel push drum to one side reached in took out four screws on back of washer removed siphon break from ebow for drain hose pulled siphon break to front of washer cut hose clamp installed new part reversed procedure to put washer together Tested operation worked fine no leaks no water on floor wife very pleased with fix Thanks again for fast delivery and great inventory of parts

Removed the front of the washing machine. Located & removed the water inlet valve from it's mounting on the back
inside face of machine. Replaced water valve, & restarted machine. Like new again!

Can't say enough about the speed of parts delivery & professionalism and accuracy recieved from the team at Parts Select. Thanx again,

Greg W.

I ordered the water valve at 12:42 PM one day and received the part at 10:25 AM the next morning. Now this is what I call excelent service. The price of the part was very reasonable. Getting my wife off my back for her washer being broken PRICELESS.

My husband did this repair. He disconnected the old part, laying them out in the order that he took them off. He put in the new part and hooked up the hoses and we had a working washer again. I ordered the part and a couple of days later it arrived on our door step. Thank you for your speedy delivery. We live in a parsonage and the washer & dryer that were in here stopped working, so we brought our Maytags (used) from our camp where the problem occurred because of winter freezing. Thanks to Maytag for making this repair so easy.

Great service! Part arrived within two days; installation instructions very
clear; washer back in service after15 minute installation. Thanks!

I removed the front of the washer then lifted the top up and swiveled it to the right. The solenoid is located in the back left. I remove the solenoid retaining screws from the the back of the washer, pulled the wires form the connectors on the top and bottom solenoids (hot and cold) and removed the defective valve. The new unit fit exactly! the total time to replace the solenoid valve was 25 minutes.

unplugged electricity from socket, turned water feed off at spigots, put plastic basin to catch water under place where hoses connect to washer, used pliers to turn disconnect hoses from washer and let them drain into basin. unfastened top screw on panel (only one) and tipped the old water inlet valve connections out over basin -- still spilled water onto floor, though. unfastened two screws holding old valve assembly to panel, set panel aside. loosened clamp screw on hose, moved hose off old valve -- a little water spilled out. held new assembly in similar position as moved wires one by one. used dry cloth to make sure electrical connections dry, then put hose back on, tightened clamp screw, fastened assembly to panel, fastened panel to washer, fastened hoses to valve, waited a half hour hoping any water on wires had dried, turned on water, washed clothes -- success!

Made sure I had the right part. Inlet Valve looked just like the one on the website. Unpluged washer. Removed screws and water hoses. Disconnected wires from old Inlet valve and reconnected to new Valve. Disconnected water line from Inlet valve to washer tub. Reconnected water lines. Ran a test cycle. Works great. Wife very happy. Therefore, so am I.