LAT7300ABX Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- LADDIE from HUTSONVILLE, IL
- Parts Used:
- 205613
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Water would not shut off. t
Followed web instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Oviedo, FL
- Parts Used:
- 206638
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Small puddle of water after the washer went through a complete cycle
I removed the two screws that held the front panel in place. Then I removed the two screws that held the top down. This allowed me to see the siphon valve when I lifted the top up. I disconnected the hose from the pump to the siphon valve by taking off the 2 clamps. Then I went to the back of the washer and moved the drain hose from the back by looseneing the clamp. Then I unscrewed the 4 screws holding the siphon valve in from the back. I took off the old valve put the new valve in and reversed the process to reinstall. It fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tevis from Albemarle, NC
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Cold water would not enter washer.
Change the position of electrical connection on inlet valve before installation to match positions of old valve. Shut off electricy and water to washer. Disconnected water hoses, and power wires to old valve. Removed old valve and installed new valve exactly as installed on old valve. Washer operated perfectively
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from Hathway Pines, CA
- Parts Used:
- WP76314
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
The hot water supply hose developed a bulge that was due to blow soon.
Shut off the hot water supply (pretty sharp eh?). Disconnected the hose from the hw supply and the at the connection to the washing machine. These had not been touched in at least 15 years and were somewhat tough to loosen but finally came ..... accessibility was a problem for the connection to the water supply as it was in a recessed wall box. Fortunately, we had some washers for the hose connections so the install was a snap. Hardest part of the whole job was moving the washing machine out from between the drier and the wash tub .... tight fit. Thanks for the quick service and to FED EX for their delivery. The delivery fellow was a real gentleman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cas from Cary, NC
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
After first spin, cold water comes in for rinsh, the water would not come in, but would run out on floor.
Removed old valve and replaced with new. Wire for wire..screw for screw..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from San Antonio, TX
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washing machine was filling very slowly
I checked the inlet hoses for hard water build up and noted that this was not a problem. Then checked the hose from the inlet valve to the washer drum and determined that it was clear so I knew the problem was a faulty inlet valve. After receiving my replacement valve, I removed the old valve by removing the hot and cold water hoses and unscrewing two screws securing the inlet valve and lifting the inlet valve out the metal holding bracket. This gave me complete access to the inlet valve allowing me to remove the hose clamp and hose to the washing machine drum. The new inlet valve was an exact match so I removed the four electrical wires one by one while putting them back on the new inlet valve to insure correct electrical connections. I added a piece of one half inch plastic tubing provided with the new inlet valve on the outlet nipple of the new inlet valve to prevent leaking. I then put the new inlet valve back into the holding bracket and screwed it down. I replaced the hot and cold hoses to the new inlet valve carefully so as not to cross thread the plastic connection on the new inlet valve. After turning the water back on, I checked for leaks and plugged the washing machine back on to test it with a washing cycle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bengt from Matawan, NJ
- Parts Used:
- 206638
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Washer was leaking from the siphon break. A little difficult to find, as the water would ru down the drain tube & make you think that the leak was elsewhere.
I removed 2 screws at the bottom front corner of the washer. Then lifted the front panel upwards about 45 degrees, which allows the front panel to be removed.
I then removed one small lag bolt from under each front corner (with a nut driver), which hold the top to the frame.
I was now able to swing the top up to have access to the siphon break.
I then removed the drain hose from the rear of the machine where it is attached to the nipple end of the siphon break, by loosening the hose clamp. Still at the rear, the nipple end of the siphon break is attached with 4 mini lag bolts, Which go through the back plate & hold the siphon break to the inside of the washer. I removed the bolts with a nut driver.
The nipple end now fell away. You must save it, as the siphon break does not come with a new nipple end.from the siphon break. Maytag attaches it with an iron band, as they must think that this repair will never be done! I cut the band with the Dremel, being very careful not to cut the hose.
I pulled the siphon break free from the hose.
The installation is a reversal of the removal, starting with inserting the siphon break in the inner hose, clamping the hose with the supplied hose clamp.
I the removed the inner drain hose
I then removed one small lag bolt from under each front corner (with a nut driver), which hold the top to the frame.
I was now able to swing the top up to have access to the siphon break.
I then removed the drain hose from the rear of the machine where it is attached to the nipple end of the siphon break, by loosening the hose clamp. Still at the rear, the nipple end of the siphon break is attached with 4 mini lag bolts, Which go through the back plate & hold the siphon break to the inside of the washer. I removed the bolts with a nut driver.
The nipple end now fell away. You must save it, as the siphon break does not come with a new nipple end.from the siphon break. Maytag attaches it with an iron band, as they must think that this repair will never be done! I cut the band with the Dremel, being very careful not to cut the hose.
I pulled the siphon break free from the hose.
The installation is a reversal of the removal, starting with inserting the siphon break in the inner hose, clamping the hose with the supplied hose clamp.
I the removed the inner drain hose
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Corpus Christi, TX
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
slowly filled with water
The hot water side would fill quickly but the cold water filled very slowly. The seloniods and the valve is built all into one unit. I ordered and replace the part in no time at all. Now both hot and cold water fill quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Jupiter, FL
- Parts Used:
- 12001413
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Deteriorated and clogged strainer; slow water fill.
Loosened the hose coupling, removed the old washer and strainer; cleaned the opening; flushed the opening; installed new strainer and washer; reattached hose and "Bob's your uncle"! No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Belchertown, MA
- Parts Used:
- 205613
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Cold water would not shut off, even after removing power.
Exactly as the video showed. This was a very simple repair. The only extra thing I did was to replace the mesh screen/gasket at the hose ends. They were plugged with crud. PartSelect saved me from buying a new washing machine. Yay!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JEFF from FORT HILL, PA
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
water coming in the wash tub when not in use
I took the hot and cold water hoses off with pliers.and then I took the one screw out towards the top of the water inlet valve plate.disconnected 4 wires,there is a small clamp on the small hose on the valve you have to remove.and last there is a cluster of wires that has to be removed from a bracket and (it is important to put these cluster of wires back in place otherwise they will wear a bare spot in them.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from North Billerica, MA
- Parts Used:
- 205613
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Slow fill using hot water
My experience with my repair is as follows:
After determining the "hot water" solenoid was weak and that a new fill valve was needed, I placed my order with PartSelect on Thursday and to my suprise, had it in my hand Friday evening (no special shipping). WOW talk about fast! But unfortunately the part was broken.
Called PartSelect back Saturday morn to explain my problem and was told that I would be credited for the broken part and that a replacement would be sent ASAP probably arriving on Wednesday. Again to my suprise, the part arrived on Tuesday morning.
Hats off to you guys for great service, prices and no hassles.
Dennis Fleming
North Billerica, MA
After determining the "hot water" solenoid was weak and that a new fill valve was needed, I placed my order with PartSelect on Thursday and to my suprise, had it in my hand Friday evening (no special shipping). WOW talk about fast! But unfortunately the part was broken.
Called PartSelect back Saturday morn to explain my problem and was told that I would be credited for the broken part and that a replacement would be sent ASAP probably arriving on Wednesday. Again to my suprise, the part arrived on Tuesday morning.
Hats off to you guys for great service, prices and no hassles.
Dennis Fleming
North Billerica, MA
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from Pearland, TX
- Parts Used:
- 205613
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
water stopped flowing
pulled the front panel first, then lifted the top(2bolts in each).
Then unhooked water and unbolted the water inlet valve from the back left corner behind the tub.four wires are connected Pay attenion to where they go, for easy reinstallation.NOTE: watch the clips in the front of the washer they flew off and it took half an hour on the internet finding out how they went back on.
Then unhooked water and unbolted the water inlet valve from the back left corner behind the tub.four wires are connected Pay attenion to where they go, for easy reinstallation.NOTE: watch the clips in the front of the washer they flew off and it took half an hour on the internet finding out how they went back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Colmesneil, TX
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
water continued to trikle in machine
took hose off then took three 5/16 screws then clamp off reversed order to put back on check for leaks ok
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Troy, MI
- Parts Used:
- 205613
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Washer would not fill unless "cold" setting selected.
I watched a sample repair on YouTube and read the instructions that came with the part. All went as planned/described.
Was this instruction helpful to you?
Thank you for voting!