LAT7300ABX Maytag Washer - Instructions

First thing unpluged power cord from wall outlet, removed hot and cold water supply hoses.Then took out srew holding metal plate ,pulled plate out exposing valve, marked wires and diconnected.Pulled clamp and hose from valve.Pulled out valve and reinstalled new.Reconnected wires and hose.Installed screw to hold in place, reconnected hot and cold supply hoses.Plug unit back in. Job done.Washer works like new.

First removed 2 screws(phillips) at bottom of front cover and lifted front to remove. Then removed 2 3/8 screws from under top cover and lifted cover and slid forward to exposed Syphon Break. After running briefly on spin, it was easy to see where the leak was. Syphon break was installed in 5 minutes by removing both hoses and 4 hex screws and reinstalling. Part arrived as promised in 3 days. I was very pleased with the whole experience.

Remove the following items: Washer to sink hose (loosen hose clamp and twist hose), two philips screws from bottom of front panel, front panel, upper side bolt screws, tilt up top washer deck and secure, remove 4 syphon break screws from rear of unit, remove pump to syphon break hose,
remove old syphon break, install new part and tighten with hose clamp, re-install pump to syphon break hose, re-assemble in reverse order. Check for leaks. Show your wife.

followed simple directions... no brainer.
just be careful - shut off water and unlug first.

Went on line an watch video that described the problem. Order the part and received it overnight. Went back online to your website and watched the video on how to do the repair. Followed the suggestions in the video and finished the repair in about 30 minutes. Really appreciate the help your company give me and have bookmarked your site for future use.

installation was difficult because the "universal" valve was a different size than the original. The solenoids were taller on the replacement valve, could not use the mounting bracket because the unit could not fit in the confined space. I also don't know why the water outlet nipple had to be smaller on the new assembly, requiring the use of a Rube Goldberg piece of tubing.

First I looked it up on the computer and clicked on Part Select's page and it came up with the part needed and then I watched the video on installing the part. It was easy to follow their instructions and the repair was made. I was so pleased with everything I ran across a man in the hardware store this morning and he was having cloths dryer trouble that I told him to just click on your site and the rest would be easy. He said he would do that. In fact I took the Wife out to dinner on just part of what money you saved me. Thanks, Harold

just like the vidio, only a had to remove the back panel to replace the valve. but we ., or should say my mother has a working wacher now,thank you for your help,

Pulled the washer away from wall and tipped forward, leaning against a chair. Removed the hot and cold water hoses. Removed 1 screw. Pulled the plate off the back of the washer. Removed two screws holding the old valve onto that plate. Took 4 wires off the original valve one at a time and placed the wires one at a time on the new valve, so I didnt have to write down or remember which wire went where. Slid one hose clamp up, pushed the hose off the old valve and placed it on the new valve. Threw the two screws back on the valve and fastened it to the plate. Put the plate back on the back side of the washer with one screw. Put some teflon tape on the threads of the new water valve and screwed on the hot and cold water hoses.

Basically the instructional video video for replacing the valve was great, but pretty obvious. Unplugged the machine. Shut off the water and disconnected the hoses (if the shutoffs are old you might need a pipe wrench or large pliers to get them completely shut off). I kept an old towel on the floor to sop up drippage. Removed the screw that holds the plate, then the two that hold the valve, all with 1/4 inch socket driver. Remove wires, loosen hose clamp on inlet hose but make sure it won't fall down into the machine. The video showed how to rotate the contacts so that they were aimed the same as on my old valve - pry up on the frame with a screwdriver and rotate until it clicks into the other slot. Just reverse the procedure with the new valve - orange and white wires to top (hot) valve, blue and white to cold. 15-20 minutes if all goes well. Note, the plate and valve attachment screws may not all be the same length even though they look the same. My problems were due to the very old washing machine. The clamp for the inlet hose was an old type that could not be loosened and had to be torn apart, luckily I had a modern 1/2 inch clamp on hand to replace it with. I had to bend the plate a little to get the attachment screw hole to line up with the hole in the washer. Also the connecting hose washers were too old and had to be replaced. I would suggest replacing these in any case and using a large pliers to get them snugly tightened.

I followed the online installation video and it worked perfectly. I am a fan of this site and would recommend it to anyone .

Removed two screws , two more on the valve, loosened the hose clamp. Reassembled the same way

With the help of my 3 year old grandson, we removed the inlet hoses and inlet panel. The water inlet valve replacement was a perfect fit. All connections conformed to the original part. I had reviewed a video at the time of order, so was familiar with the process by the time the part arrived. The website was very helpful in determination of what was needed to fix the washer problem. Shipping was fast and tracking the package provided my schedule. I will utilize this site in the future.

pulled out wash/dry stacked combo unit from cubbyhole (this was the hardest part) . Shutoff both hose supplies, turn off power to unit.disconnect power cord @ coupling. Disconnect both hoses @ machine and drain into pan. Remove old valve assembly,take note of what wires go where and disconnect. Remove filler hose from valve. Install new unit in reverse order but using new hose washers and be carefull not to cross thread the plastic threads and only tighten as much as needed to keep from leaking. Have bought from these people before and they are SUPER. Had the correct part in LESS than 24 hrs. and for a reasonable price !! Sam

Had to take the back off to replace valve