A23CSW Maytag Washer - Instructions

Tried the water level control first. didn't fix it.
Then replaced the air tube for tub fill volume.

The thing here is that it didn't have a hole in it nor was it blocked where you couldn't blow through it.
The prolbem was that at the tub end it has a larger diameter and that was nearly filled with softener residue so it changed the air volume.
That reduced air volume caused the air pressure to be wrong to the water level sensor.
My most useful tool was a magnet mount flashligt inside the cabinet so I could see to get the hose back on.

Removed two screws from bottom of front cover. Raised front cover to disingage clips and remove. Removed two screws to release top cover. Propped top cover up with mop to allow access to injector site. Removed two clamps to free injector sleeve, nozzle and valve from inlet hose. Installed new clamps, sleeve, nozzle and bracket. Lowered top cover and tested for leaks. None found. Reinstalled top cover. Reinstalled front cover. Washer back in service.

Turn the water supply off. Disconnected the hot and cold hoses from wahing machine. Unplugged the machine from power supply. Removed two screws holding the water inlet valve to the machine frame.
Took the old valve out and marked the wire connectors. Removed the wire connectors and the remaining hose from the old valve. Took the new valve and connected the wires paying attention to the markings made earlier. Uses the little adapter hose which came with the new valve to make the new hose connection on the outlet side of the valve. Put everything back and it worked fine.
These partselect guys are very prompt in sending the things you order. I have used them many times and am very happy to deal with these guys.

I went to the Internet and saw how to pry the front panel off the washer. This gave me access to the two belts and four pulleys underneath the washer; a pair for the Drive and a pair for the Pump. There was enough slack in the original belts that they came off with minimal effort. The new belts were easy enough to install. It took a mere seconds to install the new Spacers on the Front panel of the cabinet. The most time consuming portion of the project was getting the washer turned out of its tight corner to get access to the clips on the bottom of the front panel.

It was as simple as leaning the machine back far enough so I could get to the belts - which were on the bottom. The diagrams that came with the ordered parts were right on. This is the first time I have attempted this myself - my repairman has retired - I'm sure I will do it again.

Removed front access panel--very easy, two screws at bottom of panel, near the floor. Removed two more hex-headed screws that secure the top panel/lid to the top of the washing machine frame.
Most difficult problem was identifying the source of the leak. I saw water running out of a white, rectangular (about 1" x 3/4" x 3/4") box-like device that was installed in the water line that leads from the mixing valve (blue box, mounted at the back of washer) to the top of the tub. Discovered this device is called the injector assembly, have not yet been able to figure out what function it serves.
Disconnected one of the hose clamps that secure the injector assembly to the water hose. Removed the rubber injector valve and injector nozzle, the two parts that fit inside the above-described "box." Soaked the assembly "box" in vinegar to eliminate hard-water deposits. Replaced the two internal parts (injector nozzle & injector valve) with new (about $15, including shipping). This almost resolved the problem, still saw a small amount of water leaking from the whole assembly, but only about 5% of what was leaking. Haven't yet figured out why it's not completely dry, or what function that injector assembly serves.

Removed the front panel. Then blocked up the front of the machine. Removed the pump belt. Removed the 3 5/16" screws from the bottom of the old one and tilted it slightly to remove. Put the new one in and reinstalled the 3 screws. Put the belt back on and slid new pump all the way to the right and tightened 1 screw. Loosened the screw until there was about 1/4" of gap when squeezed the belt together. Tightened the one screw, then the other 2. Put the front panel back on and lowered the machine. New pump works great.

Followed the procedures recommended for replacement of all the parts included in the Tub Bearing Kit and the Mounting Stem/Tub Seal kit as illustrated in a detailed, 32 minute repair video for the Maytag A606 washer which is available on YouTube. Many difficulties were experienced in the disassembly procedures due to extensive corrosion of tub bearing and tub stem parts (the washer is 47 years old).
I was not successful in using a special tub wrench that was purchased to break loose the old tub mounting stem and its threaded lock nut. The old tub mounting stem, lock nut, and the tub bearing race had to be cut off the threaded support shaft using a saws-all electric tool. Finally, corrosion on the edge of the tub caused problems with water leaks once the tub top and its rubber tub seal ring were reinstalled and the washer was put back into operation. The bottom line is that it may be questionable to attempt major repairs on washers that are 40+ years old and have any extensive corrosion in internal, mechanical parts.

Removed front, loosened top & tilted up. Placed tub top assuring it would not rub inner basket. Placed clamp on Ridge & gasket & tightened. Reassembled & started washing.

Actually, the loud noise would happen only when valve shuts down water flow after filling up the washer (when water flow stops and washing cycle begins).
Replacement part was almost exactly the same. I did not need little transparent hose piece (used clamp that was already there). I used a combination of repair tips others already listed here: unplug washer's electricity cord 1st ( turn water off ; unhook hoses from back of washer(...); remove top screw off of inlet valve's back panel first and push up/out the bottom; unscrew valve off of panel; without yanking things around much, note exact connections of cables & hose(s); replace with new part, and put back on in reverse order.
One important note: the new part's screw holes were ungrooved but not too hard to slowly work in the screws because of the soft alloy. Be patient, good luck!
PartSelect: Great website/catalog, great service.

Removed two screws and lifted the control console then tilted forward the shell. Removed two screws holding the latch cover and assembly then disconnected two wires. I played with the assembly until I discoved the element was toast. Ordered the part but when I got it I was confused because it had three prongs (two on one side and one on the other) when the burnt one had only one and one and I only had 2 disconnect wires. I thought I had gotten the wrong part but figured it out. Actually putting the assembly together was the easy part, trying to get the outer shell back together was a little tough. Between taking it a part, figuring out what was wrong and ordering and receiving the part was about three weeks. So when putting it all together took awhile but I did it and it works great.

My washer is very old but in very good condition, it was my mothers when I was a teenager and now I am 50! This is the first repair ever done on it, my son was sure I should just buy a new one but my daughter and I had other ideas. We went on line and looked it up and followed easy directions and found the small part that was leaking right away.It had just worn out. we then ordered the parts for under $20.00 and within a few day's it was here and we were back in the laundry washing. Thank you soooo much, we are not going to let this one down with my son for some time =)

I turned the water off, detached the hoses and unscrewed the water inlet valve. I unhocked the wires and reattached the wires in the correct sequence on the water inlet valve. Done in 15 minutes.

Found the 35 year old Water injector hose was dry, brittle, and cracked. Found the new part online at a reasonable price, but was unsure if the seal came with it or not. At $3 it was worth the gamble to buy the seal. Turns out that it did come with it so in another 35 years, I'll be ready ;-) Simple replacement of the hose, one hose clamp and fitting the lip of the new seal into the hole in the top of the tub. Access was gained quickly by removing the front panel (2 phillips screws) then removing 2 sheet metal screws in the front top corners and swinging the hinged top upwards. Piece of cake.

Turn water off, removed water hoses. removed plug from elec. outlet.Then remove water inlet valve.very simple.