MAH21PDAGW Maytag Washer - Instructions

When I looked up the part number, there was an installation video on the same page. I ordered the part then and there, and once it arrived, I put the iPad right on top of the machine and paused the video whenever I was doing the steps. It was TOO EASY!

I am happy when PartSelect included the instruction video, so I completed my repair that easy. Thanks the PartSelect. Davis Dao

My 16 yr old son replaced the door boot. He said it was very easy although the wire was alittle tricky. But all in all it was very easy for him. Saved me alot of money.

Removed the door removed the hinges removed the screws holding the inner door in place removed all the parts under the inner door put everything back together in the opposit order from taking it out replaced the door wala! finished

I removed the rear access panel, used a nut driver and pliers to remove the old hose. I tried to connect the new hose with the spring clamp on the pump end of the hose. I gave up on that after a few attepmts because the clamp was very hard to manipulate with standard pliers. I used a standard screw type hose clamp (2") that I had instead. The tub end was easier because a standard hose clamp was used there already. The washer no longer leaks, and I saved a lot of money by doing the job myself!

I opened the back of the washer, put the isolator in the hole it belongs in. I then inserted the motor pivot pins into the holes, and installed the motor bolt. Installed and tensioned the belt, tightened the motor bolt, and installed the back cover.

Syphon Cup is made one way and just slides into place...very easy

Unscrewed old screws, removed old plastic pieces, and replaced

With the video you had on your web site, the repair was very easy. couldn't be any happier. you saved me from buying a new washer!

I followed the video instructions provided, without the slightest problem. I was proud I was able to accomplish this on my own. My husband wanted to buy a whole new washer, that seemed silly, so I fixed it in about 20 minutes. And no more leaks!

I follwoed the detailed instructions provided via the Part Select web page and instructional video. This information was very helpful. I printed the step by step paper instructions and had them available at the washer. They were very easy to understand. By doing this work myself I saved a $100.00 repair service call and installation cost and another $30.00 on parts. This resulted $130.00 ++ savings and 30 minutes of my time. Thanks for the great help and guidance!!

Removed the door from the washer and removed the screws holding the broken door panel to the outer door. Removed the clips that hold the screws in and transferred them to the new inner door panel. Removed the drain pipe and gasket (I assume that's what it's called) by unclipping the bottom from the door. There is another metal ring that had to be unscrewed. Then we screwed it to the new door panel and installed the gasket and drain pipe. Attached the new inner door panel to the outer door and screwed the door to the washer. Fairly easy repair.

removed screws holding inside panel switched clips and reset and replaced screws in outer door panel. Now works with no leaks

Followed the instructions that were supplied with the Lip Seal Kit, for removal of the inner drum. As expected, once into the project, I found that the bearings that are part of the outer drum, were bad. Reading other installation blogs, prior to starting, I knew the bearing sizes, 6206-2RS & 6207-2RS, and I purchased the bearings, from Motion Industries, before starting the project. Taking a hammer and long 1/2" socket extension I was able to remove both the inner and outer bearings form the outer drum. (Bearings were all but seized up) Once I had cleaned up the aluminum hub which is part of the outer drum and where the bearings mount, I was able to start the process of installing the new bearings and completing the project. Timing could not have been any better to take on this repair project because the aluminum hub was showing major signs of corrosion on the inner side of the hub. I was concerned that the new lip seal would not seal off the inner drum from the bearings/outer durm. This project was competed on 8/21/12 and so far and 6 loads later I have not found any leaks.

Followed the PartsSelect video for the seal replacement, which was step by step and spot on, I just had to add the bearing replacement part myself. Once it was dissembled I drove each bearing out by tapping them with the hammer and drift. My model had no bearing retainer ring. I did not remove the outer drum from the washer. Clean the aluminum hub real well, scrape it with a utility knife to remove corrosion, wipe with a solvent soaked rag, etc. I disagree with other methods ive seen while researching, like a wire brush in a drill, because you will remove aluminum material from the hub and the bearing wont fit as tightly as designed. tap in the rear bearing til fully seated. I did the rear first because gravity then held the spacer in place. Set the spacer in place, noting that one end is "flared" to a larger diameter, so it seats against the larger race of the front bearing. Align and start the front bearing in place. The spacer needs to align with the bearings so it bears against the inner races of the bearings. So to hold it in place I rolled up a piece of light cardstock, slid it thru the spacer and bearing, and as it "uncoiled" it aligned the spacer. Pretty well. I did have to tap the spacer a little with the drift after the bearings were in, but just a little. After that, back to the video for the seal and reassembly. Only other comment I have is to locate the bearings early. I ended up going to grainger for one and Napa for the other. And no one could seem to cross the "DU" part of the original NGK bearing. The DU means it just has seals on both sides. Pretty standard stuff. That could have been easier. Also hold off ordering extra parts. I have found PartsSelect is really quick getting stuff out. I ordered an inner drum because i heard from other research that that could cause the banging noise. My banging noise was from one bearing disinegrating and the balls breaking up inside the hub. Shipping the drum back cost 70. UPS wanted 160. So that could have gone better, but I didn't want to let the machine sit too long. Next time I'll let it sit a couple days.