MAH21PDAGW Maytag Washer - Instructions

I referenced the enclosed instructions, and U tube videos, along with gasket I also changed the bearings for about $40. From local grainger, it seems to have solved problem, thanks for quick shipping,

Basically the problem was the bearing replacement. Although you cant get them on PartsSelect, I got the seal kit on the site. The seal kit is easy, the bearings took two days and an air hammer to extract them and a big hammer to get them back in. All in all it was worth it,

What transpired was removing the guts from the old inner door and putting them onto the new door which extended the time. Not sure about the tools because my handyman/friend did the installation while I was gone. He was a little frustrated with it. Otherwise, the door fit well. We decided that using hot water was the problem with the water leaking from the door. Using cold and warm water settings seems to make a difference.

The video was great. The only problem was getting the spring back on. It was way too stiff, so I put it in a vise and stretched it a bit. It's a bit fussy but your site made it go pretty easy. thanks

I just followed what others have already noted. The only challenge was the spring as others have already stated many times. You will need help but be patient and you'll make it work.

On-line instructions were found easily enough. And followed easily. Hard part was placing the cable and spring which secures bellow on drum. One instruction said "you cannot do this by yourself" (I couldn't see how help would have "helped") the other said "this was the hard part" of repair. I weight 115 lbs and it took me 1/2 hour to finally get the spring hooked through cable end it's a very STIFF spring! I only had a short pair of needle nose pliers - an 8-inch pair would have given me more leverage and shorten "hook-up" time.

I followed the video which I might say is somewhat misleading for the Maytag Neptune washing machine. This is the one with a recall due to mildew and mold build up on the Door Seal (Bellow). First to take it apart you really need a 8mm socket in order to get into tight spaces. Once you start using the socket everything will come apart quickly the last being removing the old Bellow. I found this is easy if you just roll the spring toward the front using a screw driver. Once it clears the front of the Bellow, the cable will fall off along with the spring. You can now remove the old Bellow. The next step is to insert the new Bellows on the rim of the tube. I started by attaching the drain hose at the bottom and then from the video, started at the top make sure you have it center correctly and worked down one side pushing the Bellows on the rim and then do the same thing to the other side part way. Alternating from one side to the other until you reach the bottom. The Bellow is now on the tube, NOW the hard part. First, the old spring was stretched. I bought a new spring at Home Depot. I next took the cable and placed it around the tube with the ends at the top. Make sure to thread the cable carefully so it is in place. Watch out for plugs and the drain at the bottom of the tube. I attempted to attach the spring by myself using a long nose plier and a Grip plier but just could not stretch is far enough by myself as shown in the video. I next took a 16 ga insulated wire you could also get at Home Depot and attached it to each end of the cable and twisted it together in the middle with pliers so it was tight and cut off the excess wire. I attached one end of the spring through the right eyelet on the cable and using the grip pliers and BOTH hands on the grip pliers pull the spring and threaded it through the left eyelet. Hold the spring in place I now pushed the stretched spring against the back lip of the tube. I removed the 16 ga wire buy cutting off the ends and carefully pulling it away. Next, I just followed the video. I pushed all the tabs on the Bellow in to the holes on the tub and then screwed the parts back in reverse order. Good Luck Al

Followed the video, besides the spring, everything was easy.

This is a stacked Neptune washer. You must take the door, front covers of the machine, plus remove the light and wax motor section to the side. You must disconnect the bleach and softener dispenser connections near the bottom of the washer to get the front portion off so that you can get to the boot. Catch the excess water in a pan to avoid getting the electrical circuit board wet. Take the boot off. This is easy, but the spring that holds the small cable around the boot is a bit tough. You can do this with the needle nose vise grips. Place the boot on the tub first making certain that the small notches in the boot line up properly onto the washer ridges. I had to use a 2 X 2 to pry the tub down so that my friend could get the boot lined up on the tub. Some stretching of the boot is required. Place the cable around the boot on the washer and use a strong mason's cord or similar cord and tie the ends of the cable as tight as you can get it so that the cord holds the cable in place. Place one end of the spring into the cable end and taking the needle nose vise grips pull the spring until it can be placed into the other end of the cable. When finished, take a knife and cut the cord and pull it out. The spring is very strong so it is difficult to pull it into place. Since I am old, I had to enlist a friend who is an appliance repairman to get the spring on. That is the most difficult part. Lastly, you get some dish soap and place around the inner part of the boot where it fits onto the other section of the washer so that you can get it on easily. Reassemble the parts and everything should work OK. Don't remove the plug at the bottom of the new boot unless your washer happens to have the drain connection.

1. ReMoved spring and cable from tub, 2. Remove bellow drain hose clamp at bottom of bellow, 3. Remove bellow from tub side and door frame, 4. Wet door frame with water and dish soap solution, 5. Press door frame side of bellow into slot. Align grooves, 6. slide tub side of bellow over tub edge, 7. Say a prayer to the good of your choice, 8. Reattach bellow cable with spring. This required use of double stands of 60lb braided fishing line to chinch most of the way and then use of a spring hook took in one hand and needle nose in the other. No less than 12 attempts. Be sure to have another pair of hands ready when doing and the whole job will take about 15 to 20 minutes.

The front seal had a long slit which leaks water during washing cycle. We followed the repair video every steps and got the old seal off really easy, the most difficult step is to tie the cable with the spring, it is too strong and can not be done with one person. All steps are the same as shown in the video. Thank you for providing the video and the part.

I watched the provided video that EXCELLENTLY showed the replacement of the part. Then I was able to complete the task with no trouble at all

Moldy bellow was the reason I replaced the bellow. It tried cleaning the bellow numerous time over the last five year, but once the mold sets in, it's a losing battle. A highly mold resistant bellow would be nice. The available video was invaluable. I would not have purchased the parts if I had not seen the video. I spent a few more dollars for additional parts, because once I got started I did not want to find a bad part and then not be able to complete the repair in one try. Since the bellow was moldy, I expected the door boot drain hose would be moldy also, so, for a few more dollars, I replace it also. Worth the effort. I took me, just under two hours to complete the job, with the help of my wife. I'm some may be thinking, what did she do? She cleaned the parts I took off, so they were clean, well at least cleaner, when I put them back on. This washer was nearly ten year old and had never been apart. I could have finished the replacement bellow in less than an hour, but I took some time to clean inside the washer while it was apart. That's just the way I roll. Fitting the bellow to seal properly was not as simple as the repairman made it look on the video, but that was because he had done this before, probably many time over. He knew what it felt like to fit it and snap it into place. Once I got the feel of seating the bellow, it went smoothly. The boot cable and spring are a bit tricky to hook, as anticipated; I read some previous experiences. So, I thought about how I was going to secure the spring in order to stretch it to the other cable hook. I decided to use two pairs of vice grips to hold the spring and cable hook end. I have two small to medium sized vice grips, which worked perfectly. Otherwise, it is very difficult to pull and hold a pair of pliers closed, at the same time. I sit at a computer most days and am not used to a mechanics world. Use your brain when you don't have the brawn. Job done, no leaks.

Had to remove the door, the face of the washer, and two face pieces between the washer and the stacked drier. I then removed and replaced the bellow. The installation of the new bellow was difficult, the first time. Getting the silicone part onto the tub is tricky as is re-installing the cable and spring. I must have not gotten the cable properly seated on the lower lip as it leaked and I hade to repeat the job the next day. The second time around was much easier. There is a learning curve, even for me, a retired electro mechanical tech. I thing someone who is not very handy would have trouble with it. This repair should be considered only by someone of intermediate or better skills.

I followed the video for the installation. I did find that installing the spring was no way as easy as it looked in the video. Otherwise, OK.