MAH21PDAGW Maytag Washer - Instructions

Off with the door. Off with the front panel. Lift the top and you are looking at the boot. Remove the boot retaining wire . Remove the boot and reverse the procedure. It's a snap.

Basic disassembly as described earlier.Some tips I found helpfull. Use vice grip pliers on spring.it will keep a grip on the spring hook and you can exert more force to pull the spring.Th bellows was very sticky and hard to slip into place. I put a litle silicone lube ( stuff you use for pool pump gaskets )on the bellows. It made it slip into place easly.

Removed the door and front panel with ease. Then came the spring and cable. People who say it was easy are not telling the whole story. Removing the spring was okay except for it flew across the room. Putting the new cable on with a pair of needlenose pliers did not work for me. I had to get a spring tool like you use on brakes on a car. Once I had the tool and secured the cable in place with a piece of wire I got the spring on. Everything except the spring took about 15 minutes.

I went on your site and found out the Bearings were not sold separately by Maytag and that they wanted $800.00 for the entire outer tub in which the bearings are pressed into. I read another post on your site where someone referenced some NSK bearing part numbers. I went to my local auto parts store that cross referenced the NSK number to Timken Bearings (a high quality automotive bearing). Following the instructions I hammered out what was left of the old bearings cleaned everything and pressed in the new bearings. When the Lip Seal kit arrived I pressed in the new seal following the instructions provided, reassembled the washer and it’s as good as new. Total cost just over $100 in parts and a few hours labor. Removal of the old bearings was a difficult task especially since mine were in such bad condition as water must have been slowly leaking into them for some time. If you have some basic automotive repair skills and or some knowledge of how to remove and replaced pressed in bearings I would recommend this repair. In my case money was the motivating factor with 2 kids in college and a wife who would have insisted on a new matching set of a washer and a dryer instead of just replacing the washer.

I was sick when I heard the noise from our washer. I looked online at new ones and found out it was going to cost between $1000 to $1500 to replace it. While looking online I found the PartSelect site. Unbelievable! I put in the model #, read the posts, ordered the parts and within a few days they were in. Using the video and the posted instructions I took it apart and replaced the bearings and seals. The whole thing took about 3 hours and we were back to washing clothes. Total repair costs were about $160 to $180. Compared to the price of a new washer, you guys saved the day.

Accessing the bearing housing was quite easy and the PartSelect videos were quite informative. Upon removing the lip seal the bearings obviously needed to be replaced. The bearings needed to be purchased from a local supplier and we used Grainger #6L028 (rear bearing) and #6L029 (front bearing). We needed to apply a generous amount of Liquid Wrench and used a long drive punch pin and a 3-jaw pilot bearing puller to remove the bearings. After removing the rear bearing we broked the puller on the front bearing, but were able to remove with the punch pin with the access created at the rear of the drum. Reinstalling the bearings was text book, we used a long bolt with large washers to pull the front and rear bearings together, with the spacer inserted between them.

Replaced it with the new inner dooor.

My first time attempted to repair washer and step by step video instruction attached with order confirmation did it for me. Thank you

What transpired was removing the guts from the old inner door and putting them onto the new door which extended the time. Not sure about the tools because my handyman/friend did the installation while I was gone. He was a little frustrated with it. Otherwise, the door fit well. We decided that using hot water was the problem with the water leaking from the door. Using cold and warm water settings seems to make a difference.

Replaced the inside door panel. Who needs a Maytag repairman! Thank you for the great instructional video.

The front seal had a long slit which leaks water during washing cycle. We followed the repair video every steps and got the old seal off really easy, the most difficult step is to tie the cable with the spring, it is too strong and can not be done with one person. All steps are the same as shown in the video. Thank you for providing the video and the part.

Follow the suggestions on the rope tied to the side of the washer, then mechanically lever the spring open. Only change I would incorporate is using a block of wood to keep the wash drum from moving over as you pull on the rope to open the spring up. GREAT AND EASY FIX!

I just followed what others have already noted. The only challenge was the spring as others have already stated many times. You will need help but be patient and you'll make it work.

On-line instructions were found easily enough. And followed easily. Hard part was placing the cable and spring which secures bellow on drum. One instruction said "you cannot do this by yourself" (I couldn't see how help would have "helped") the other said "this was the hard part" of repair. I weight 115 lbs and it took me 1/2 hour to finally get the spring hooked through cable end it's a very STIFF spring! I only had a short pair of needle nose pliers - an 8-inch pair would have given me more leverage and shorten "hook-up" time.

I followed the video which I might say is somewhat misleading for the Maytag Neptune washing machine. This is the one with a recall due to mildew and mold build up on the Door Seal (Bellow). First to take it apart you really need a 8mm socket in order to get into tight spaces. Once you start using the socket everything will come apart quickly the last being removing the old Bellow. I found this is easy if you just roll the spring toward the front using a screw driver. Once it clears the front of the Bellow, the cable will fall off along with the spring. You can now remove the old Bellow. The next step is to insert the new Bellows on the rim of the tube. I started by attaching the drain hose at the bottom and then from the video, started at the top make sure you have it center correctly and worked down one side pushing the Bellows on the rim and then do the same thing to the other side part way. Alternating from one side to the other until you reach the bottom. The Bellow is now on the tube, NOW the hard part. First, the old spring was stretched. I bought a new spring at Home Depot. I next took the cable and placed it around the tube with the ends at the top. Make sure to thread the cable carefully so it is in place. Watch out for plugs and the drain at the bottom of the tube. I attempted to attach the spring by myself using a long nose plier and a Grip plier but just could not stretch is far enough by myself as shown in the video. I next took a 16 ga insulated wire you could also get at Home Depot and attached it to each end of the cable and twisted it together in the middle with pliers so it was tight and cut off the excess wire. I attached one end of the spring through the right eyelet on the cable and using the grip pliers and BOTH hands on the grip pliers pull the spring and threaded it through the left eyelet. Hold the spring in place I now pushed the stretched spring against the back lip of the tube. I removed the 16 ga wire buy cutting off the ends and carefully pulling it away. Next, I just followed the video. I pushed all the tabs on the Bellow in to the holes on the tub and then screwed the parts back in reverse order. Good Luck Al