MAT13MNDGW Maytag Washer - Instructions

all went well until testing. tub level did not shut the water off, caused a spill

I removed the two screws holding the switch and removed it from the machine. I then removed the broken spring and replaced it with the new one sent to me from partselect.com. I reinstalled the repaired switch and turned on the machine. It was easy as that and it works great. PartSelect.com is the best.

Repair not that complicated. Remove front, lean top back, remove agitator, remove special nut, remove inner tub, remove seal. Clean shaft and seal surfaces. It is highly recommended to the spanner wrench to remove the special nut. It appears one can do it with a punch and hammer, but the nut is too tight, and corroded from years of water exposure. I believe part number is TJ90TB123A, about $15. Watch the video on this web site, very good.

First I removed the two screws that held the front washer panel in place. Then I removed the two bolts that held the top on the washer. I then had to remove the four screws that held the top panel with the electrical parts in place in order to obtain access to the inside area where the screw was that held the fill injector was located. I next removed the screw that held the fill injector unit in place. I then pulled on the tab that held it in place and moved unit into a better place to replace the fill injector. I had previously cut the hose clamp during my investigation of the problem and replaced it with a pressure clamp. I then unscrewed the clamp, removed the bad fill injector and replaced with new fill injector. I then reversed the entire process to reassemble. The whole process turned out to be easier than I thought! The hardest part was diagnosing the problem in the first place.

I opend up the housing, found the broken part, ordered it, installed it, and had the washer working within 4 days of the initial break down.
Saved a lot of money over a service call, as well as time, and trips to the laundramat.

Viewed the very helpful video on your website, that spelled out all the steps to follow. The key point is to not forget the spanner nuts are left handed threads - even after noting that from the video, started the removal in the wrong direction, then caught my error and moved on through the disassembly process. In my case, I took time to deal with a lot of soap buildup cleanup in the outer tub, and even cleaned and put rust inhibiting paint on a few spots to try to get a little longer life out of the old machine. This repair cost far less than replacing it, and should get us several more years of service.

Found the parts I needed on your website along with a video that showed exactly how to do the repair. Set my iPad on the dryer and followed along step by step. Never would have tried something like this without your helpful information.

I replaced the 3 screws because they were rusty. Then I replaced the Drain pump

Replaced hose. Really appreciate Instructions, especially from other customers. Only thing I didn't have was new hose clamps, since this Maytag washer is 35 years old! (Love it! Works great!) Old hose clamps were absolutely rusted beyond any possible recovery, so I had a little trouble getting them off until I sprayed them with penetrating oil. Buying local clamps not a problem.

First I took the door off. Undid two screws that held the top door on. Took the tub out. Make sure you have a spanner wrench. So much easier.

This washer was purchased in the early 1980s and is different from the one in the video and other repair instructions. You can recognize this earlier model by the agitator design. It only has the 4 paddles that start at the bottom and does not have the auger design on the upper part of the spindle as the newer ones do. While I was able to get the agitator to pop off by threading thin ropes under it and using a four-foot board as a lever, that was the end of my successful efforts. Even with the special tool and a five pound hammer, the lock nut would not budge -- even after overnight soaking in WD40. Yes, I did recognize the reverse threading. My next attempt would have been to heat the lock nut with a butane torch, but I gave up at this point and purchased a new washing machine on my way to pick up the torch. Would be curious to know if anyone else has had success with this older model as I saw other differences in the design that suggested that it may not have been compatible with this kit.

key to repair is to watch the video on mounting stem/tub seal as seen thru parts select. However, they use a nice new, clean,sanitized washer that may not reflect a 23 year old washer like mine. They give you the basics and it is invaluable to watch if you have never done this before. I strongly advise you buy a real spanner wrench made for your make. You may never need it again but it makes it much easier. Trying to use a punch or using a dremmel to operate on your large 'nuts' is, well, nuts! Get the wrench, just part of the cost of repair. See ebay. The first thing I noticed different between the video and my real life unit is the water hose connected to the washer, at the top of the tub cover. This did not exist in the video, but it is the way on my unit. So I did not disconnect it, just folded the top out of the way and tied it up. Then of course my real gripe with the video is that I have the old time band around the tub and the barrell, holding them together. They do not mate up very well and are not easy to put back together properly. In fact, installing the stem seals was easy and it fixed the original leak. I might add when you buy the replacement parts, you actually get 3 new parts. I suggest you use all the new parts in the package. You paid for them, you need them. Again the video only talks about replacing the very bottom seal, never mentioning the other parts they sold you in the bag. It is easy to figure out how to replace the other parts, they look like the ones you took off to get to the very bottom seal. Use all the new parts, regardless. So the only real issue is putting the band back on to hold the tub to the drum. We did not get it correct the first time and the unit would not spin, I had the top down too far. You could smell the rubber burning from the drive belt. They forgot to tell us about that!! Bums. So we loosened up the band, raised up the top piece and got it to spin. Of course, we did a large load, filled the water to the highest level allowed and when the unit hit the spin cycle, we got a leak from under the band. Thx video. To fix that we decided to never use the highest water level. So far so good. I can tell you the engineers failed on the design to mate up the cover to the tub. Other than that this can be done by us goobers, just take your time. And good luck. I must also thank my helper, neighbor John . for his added wisdom and support.

First I bought a Maytag spanner wrench on eBay, you have to have it. It was $12.00 including shipping. Then when the parts showed up the next day followed the video and had it done in just under an hour from gathering my tools and cleaning up. The video was perfect and I had no troubles what so ever. The quote from the repair services was $280.00 and I did it for less than $90.00

Loosened the set screw and removed the agitator, found nothing wrong. Replaced the agitator and tightened set screw, no more wobble.
This is a mid 1970 Maytag and a workhorse.Had three kids wash over the years, now "kids" in their late 30's and early 40' and washer is as good as new (except a little rusty)

First time I had a problem with it. Sometimes just look for the simple things !

Part select refunded me for my part that I ordered very fast.

Great Company to deal with!

I propped up the machine. Turned the water off .took the pump belt off, then took the two hose clamps off. With a bucket and towels on hand for left over water in the hoses, i removed the two hoses. Then removed three screws that held the pump on. Installed the new pump in reverse order.