LA7500S Maytag Washer - Instructions

Took off front washer panel push drum to one side reached in took out four screws on back of washer removed siphon break from ebow for drain hose pulled siphon break to front of washer cut hose clamp installed new part reversed procedure to put washer together Tested operation worked fine no leaks no water on floor wife very pleased with fix Thanks again for fast delivery and great inventory of parts

I removed the front of the washer then lifted the top up and swiveled it to the right. The solenoid is located in the back left. I remove the solenoid retaining screws from the the back of the washer, pulled the wires form the connectors on the top and bottom solenoids (hot and cold) and removed the defective valve. The new unit fit exactly! the total time to replace the solenoid valve was 25 minutes.

Removed old part, installed new part. tested machine. worked fine.

unplugged electricity from socket, turned water feed off at spigots, put plastic basin to catch water under place where hoses connect to washer, used pliers to turn disconnect hoses from washer and let them drain into basin. unfastened top screw on panel (only one) and tipped the old water inlet valve connections out over basin -- still spilled water onto floor, though. unfastened two screws holding old valve assembly to panel, set panel aside. loosened clamp screw on hose, moved hose off old valve -- a little water spilled out. held new assembly in similar position as moved wires one by one. used dry cloth to make sure electrical connections dry, then put hose back on, tightened clamp screw, fastened assembly to panel, fastened panel to washer, fastened hoses to valve, waited a half hour hoping any water on wires had dried, turned on water, washed clothes -- success!

Made sure I had the right part. Inlet Valve looked just like the one on the website. Unpluged washer. Removed screws and water hoses. Disconnected wires from old Inlet valve and reconnected to new Valve. Disconnected water line from Inlet valve to washer tub. Reconnected water lines. Ran a test cycle. Works great. Wife very happy. Therefore, so am I.

Removed door panel to get to the electric control conponents and noticed a burned wire to one of the door microswitches. Ordered the door switch repair kit from PartSelect. Also, ordered and replaced the thermal fuse at the same time since it was only $12 and didn't know if that blew at the same time the switch cooked. I had the parts coming standard delivery (3-5 days), but they arrived the very next day. Parts included easy to follow directions.Job went pretty smooth and the dishwasher works again Good experience!

Unplug washing machine.
Disconnect water supply hoses.
Remove valve service panel, 1 screw.
Remove valve from panel with wires attached. 2 screws.
Remove water outlet hose from old valve.
Mount new valve to panel. 2 screws.
Attach water outlet to valve.
Move wires from old valve to new valve.
Dress wires.
Reinstall valve service panel, 1 screw.
Install new wire braded supply hoses.
Done. Hope to get another 20 years of service.

My husband did this repair. He disconnected the old part, laying them out in the order that he took them off. He put in the new part and hooked up the hoses and we had a working washer again. I ordered the part and a couple of days later it arrived on our door step. Thank you for your speedy delivery. We live in a parsonage and the washer & dryer that were in here stopped working, so we brought our Maytags (used) from our camp where the problem occurred because of winter freezing. Thanks to Maytag for making this repair so easy.

Great service! Part arrived within two days; installation instructions very
clear; washer back in service after15 minute installation. Thanks!

The hot water side would fill quickly but the cold water filled very slowly. The seloniods and the valve is built all into one unit. I ordered and replace the part in no time at all. Now both hot and cold water fill quickly.

I found that the water was coming from top of syphon break. Took it out located it on computor , ordered part. Took about 10 min to replace. EASY

I removed one screw from the access panel directly below the syphon break. I removed the 4 screws that secure the elbow to the valve. I reached inside the access panel and pulled the valve towards the front of the washer far enough so I could reach in and remove the broken elbow. I inserted the new elbow and replaced all the screws. I connected the drain hose to the syphon break, connected both water lines and I was done!

Remove the following items: Washer to sink hose (loosen hose clamp and twist hose), two philips screws from bottom of front panel, front panel, upper side bolt screws, tilt up top washer deck and secure, remove 4 syphon break screws from rear of unit, remove pump to syphon break hose,
remove old syphon break, install new part and tighten with hose clamp, re-install pump to syphon break hose, re-assemble in reverse order. Check for leaks. Show your wife.

followed simple directions... no brainer.
just be careful - shut off water and unlug first.

First thing unpluged power cord from wall outlet, removed hot and cold water supply hoses.Then took out srew holding metal plate ,pulled plate out exposing valve, marked wires and diconnected.Pulled clamp and hose from valve.Pulled out valve and reinstalled new.Reconnected wires and hose.Installed screw to hold in place, reconnected hot and cold supply hoses.Plug unit back in. Job done.Washer works like new.