MAT15MNAWW0 Maytag Washer - Instructions

went really good, received both parts in less than two days, great service! Video's on line were really helpful and made taking apart and putting back together easier, even though video's were on newer model machines. Would not hesitate to order parts from Part Select again.

The new pump arrived at my door just a few days after it was shipped.

Once I got the water hoses off and the clips holding the pump I had to use a large screwdriver to get the pump off the motor shaft. I then tried putting the new pump on but it wouldn't fit. I noticed that the motor shaft was flaired out (possibly due to rust) so I used a Dremel Tool with a grinding disk to carefully grind down the shaft to what it looked like it was supposed to be. Once that was done the pump easily slipped into place. I attached the pump clamps and hoses and pushed the washer back into place. I ran a quick test and then later a load of laundry. No more leaks!

Using the part select website, I discovered that 64% of the time, replacing the water pump will fix the drain problem so I ordered that part. I laid the washer on it's back. And was able to unclip the water hoses, detach the pump and install the new one. The parts select website has great instructional videos to help but in this case, the video recommended removing the outer skin from the washer which I found unnecessary.

I propped the unit on its side, then I removed the intake and discharge hose with pliers (remember to have a bucket handy for the extra water in the hoses.)
Secondly, there are two clips on the top and bottom of the pump which hold the unit snug against the motor. These simply pop off with your hand or a screwdriver (be careful to save these!) Now the pump should slide off the drive shaft easily but most likely it will not due rusting of the shaft. A pry bar or large screwdriver and some elbow grease will get the pump to slide off.
Installation is the reverse except you will have to sand off the rust on the shaft. Sand paper will do but I used a Dremel type grinder (die grinder) which made easy work of removing the rust. Finally, sliding the new pump in is remarkably easy.
Installation of the new pump should take less than 10 minutes with a clean driveshaft.

Remove four screws securing control panel from the rear and tilt control panel forward. Unplug wiring harness from door limit switch. Unsnap and remove two S-clamps securing enclosure to back panel. Tilt enclosure slightly forward and remove it from wash machine. Disconnect water hoses and clips securing water pump and remove water pump. Install in reverse order. Caution: inspect water hoses closely. I had a rotten pump intake hose and found out the hard way (water everywhere).

Isolated problem to front section of washer by elevating and adding water. Once I identified the pump as leaking (it was pretty obvious:>)I used a screwdriver to release the snaps that hold the pump to the drive motor. After sliding the pump off of the drive motor I used the pliers I release the clamps on the two hoses. Next I logged on to Partselest.com and ordered a replacement. The item arrived in two days. I placed the pump on the motor first then connected the hoses. It was much easier to slide the hose clamps to the proper position with the pump held secure on the motor.

I read the trouble shooting guide on your web sight to figure out what the problem was and after checking the hoses the pump seemed the next most likely problem. So I ordered the part.My main problem was the lack of room to work,if I could have tipped it on it's back or raised it I would not of had a problem.But I tipped it up and blocked it from falling and removed the part while waiting for the new one to arrive.Once it arrived it only took a few minutes to install.When I tried the washer it still leaked water,so I tipped it back up to check it out.The only thing that was wrong was that the spring hose clamps had not seated yet so I moved them around and wiggled the hoses to try and get them tighter.The next time ,it worked fine.The other reviews and trouble shooting guide were a great help!

Video was very helpful. Repair was easy. Remove and replace with just hand tools. The hardest part was moving the washer around to tilt it back. Service was great. I picked regular ground shipping and parts showed up the next day.

My husband got the part within 2 days of the order and replaced the leaking pump within a half hour. The repair was very quick and easy for him and your company's prompt delivery prevented my floor from getting wet everytime I did a load of laundry. Thank you and we will continue to get parts from your site in the future--hopefully we won't need to anytime soon. but we know you are there if we need to repair!

First I watched the repair video. Then I pulled the power plug and shut the water off. I didn't have all the room available to remove the front and sides of the machine in my narrow hallway so I just slid it away from the wall and leaned it back against the wall and had plenty of room to do the repair lying on my side. $28.00 part and in 20 minutes all done. This is the second time this site saved me time and mucho money. Thank you. Leon B. from Massachusetts

I unplugged the washer, put a towel down, leaned it back and held it up with one hand while undoing the clamps with plyers. Pulled the two clamps off, pulled the pump, put the new pump on, reattached the clamps. Most of this with one hand while the other held the washer at an angle.

Pull Washer out, Flip to the right on it's side. Pop two Metal retaining clips, squeeze hose clamps with pliers. Remove pump, sand shaft with dremil or 80 grit sand paper. Replace with new pump. Easy! Push washer back and attach hoses and power. Done 15 minute repair

plires took off the two hoses , on clip the two snap clips . pulled out the old pump . put the new one in cliped in the snap clips in & hook the hoses back up

very well the part was easy to install and the part was easy to find on the diagram furnished by parts select

the hard part was getting the pump off of the rusted centerpeice. i actually had to grab the pump with both hands, put my feet on the rotator and PULL. finally it basically snapped off and rusted peices went flying. after cleaning it the new pump went on rather easily, with the help of a rubber mallet.