MAT15MNAWW0 Maytag Washer - Instructions

My friend unplugged washer turned off water to it, tilted machine back took off old, put on new. It took him about 5 minutes. Washer is working fine now, no more water leaks!

First unplug washer and turn water off (both hot and cold) You only need to pull washer out away from wall about 1 1/2 feet. Take a putty knife and slide under the front corner of the control panel ( both sides one at a time) lift up corner as you slide putty knife under the corner. After both sides are released on the control panel slide control panel forward( about an inch) to release rear of panel and flip panel over the top. Unplug the lid safety switch then with a screw driver unsnap the cabinet straps one on both sides that were under the control panel. Put screw driver into the spring strap end closest to you and push screw driver back which will release the straps( one on each side). Next tilt the cabinet toward from the back( about 6 ") and lift up about 2 " the cabinet can now be removed. Undue the two hoses on the water pump that is located at the bottom of the washer in the front ( make sure you catch the water from the hoses in a small pan). Undue the two spring clips that hold the pump on. Pull pump straight out (about 1 ") discard old pump and install new one in reverse order. When reinstalling the cabinet there are two stubs on the bottom bracket on the washer that have to put into the slots in the lower front corners of the cabinet ( the hardest part of the whole project is putting the cabinet back on, the trick is what I described above with the slots in the lower front corners. Good luck it very easy to do.

Of course I tried to determine where the leak was from. There wasn't a solid flow of water and was confined to the front. Pulled the washer out and laid it down. Noticed that a metal clip had a little corrosion on it and followed it back to the water pump seal. Removed two hoses and unclipped the pump. That's it. No screws or nuts. Looks like it was expected to fail and was easy to replace. It did last for 20 years though.

I turned the washer on to see if I could determine where it was leaking from. After I figured out that it was the pump that was leaking, I ordered a new pump. I went with next day shipping because at our house, we can't go long without a washer and the cost for the shipping was worth it. Had it installed in 10 minutes, only tool needed was a pliers to remove the hose clamps, piece of cake repair!

Unfortunately my washer cabinet did not come off as in the video so I had to do repair from underneath. The rest of the repair worked exactly like the video showed. I had a couple of small, sturdy wood boxes about 9" high which I used to brace the washer after tipping it backwards a bit (and unplugging it too). My wife acted as a spotter to be extra safe. The only two things that required the hook tool and mirror were: 1) Working from the bottom my hands were at an awkward angle so I couldn't pop the retainer clips off the pump, but a hook tool (like a screwdriver with a hooked end) popped them off easily, and 2) The other issue was once the new pump was in place I could not locate the slot for the top retainer clip until I could look at it with the telescoping handle mirror, and then I was able to put the clip in by feel. Extremely easy repair, especially with the guidance from the video. Thanks for video help! WH

undone 2 hoses and popped off brackets

Replace front legs. Very easy fix.

The repair went fine and the U - Tube video was very helpful. However, the putty knife under the front corners to release a spring clip was not accurate to release the console. Our Roper had two philips head screws on each corner of the back of the console that had to be removed to allow the console to slide back and off its clips. Then the housing of the machine (sides and front) was not coming off as described. However, after measuring I determined that the water pump had enough clearance to be removed without the housing of the machine being removed. So, the repair was even simpler than described.

Flip washer on its back, Undo/flip the clips/clamps off the water pump, remove the clamps from the hose and remove hoses from water pump, slide the pump off the direct drive, line up the shaft/drive with the new water pump and slide into position and return the clamps to secure water pump in place and reattach water hoses and clamp to the water pump. There should be two hoses going to the water pump, flip washer back upright and run a cycle to make sure the problem has been fixed

Removed the four screws from the control housing. Disconnect wire to machine housing. Remove the two clips connecting the machine housing to the back. Remove washing machine housing. Pump is located right in front. Disconnect hoses, remove and replace pump, reconnect hoses. Replace the machine housing. This was the hardest part if all trying to reinstall the housing.Once you get the machine housing in place correctly, put everything back together. You just saved about $125 in fifteen minutes.

First, we took the pump off and found that it was leaking. Ordered the part on line. The part arrived in four days as scheduled. The small pump was easy to replace with screwdriver and pliars.

Removed water supply hoses and took drain hose out of drain. Unplugged electrical cord. Turned washer over to see and reach pump easily. Flipped clips holding water pump. Moved hose clamps back on inlet and outlet hoses. Wiggled hoses off pump. Placed new pump and flipped clips back in place. Wiggled hoses back onto pump ports and replaced clamps to hold. Turned washer upright and reinstalled. Using channel lock pliers to move hose clamps was the hardest part.

I watched the instructional video on how to take apart and how to take washer a part and how to install the direct drive water pump. It was very easy to do. also the delivery was very fast. I will be using the site to fix other appiances that I have that is sitting around broken. Thanks for your speedy service and customer service.

I disconnected the washer from the water supply lines.turned the washer on it's back. took two hoses off the water pump.Unsnapped two spring clip's.Took the old pump off and installed the new pump.That is all there was to it.

I followed the you tube instructions. The hardest part was realigning the washer housing on the lower frame.