MAT15MNAWW0 Maytag Washer - Instructions

watched a video that showed how to repair that you had on your web site. also read some of the remarks that other people left on site, one was super easy. just laid washer on its back, unhooked both water lines from pump. unhooked both metal clips holding pump and pulled off. replaced new pump in reverse order. didn't have to go thru all the procedures of taking off the body or nothing. 15min job.

tilted the unit on it's back. removed clamps and hoses from pump. used screwdriver and pried off 2 hold-down clamps. removed old pump. placed new pump onto shaft. installed hold -down straps. re-installed 2 hoses. stood washer upright, releveled and turned on.

After unplugging power and disconnecting water drain hose, I pulled the washer out aprox four feet from the wall and leaned it back against the wall. I then used a lamp at the end of an ext cord to light up below the washer where the water pump was attached and it was easy to remove and replace! I carefully replaced the washer in its original location and reconnected power and drain hose. The job was complete in 15 minutes! Wow!

removed two hose clamps and two metal clips
removed old pump and replaced with new
wish all my plumbing was that easy
order Thursday night got it Monday
great job
I'll be telling everyone that needs parts about you
thanks

I pulled out the washer, laid it on it's back, pulled off the two hoses using pliers for the clamps, pulled back two clips, pulled off the pump from the shaft, put the new pump on the shaft, and did the reverse of the above. It was a simple operation and made even more satisfying by the prompt delivery of the part, within 2 days. Thank you for that, and I will use your services in the future if needed.

Tilted washer back, pump was right in the front on bottom. Removed two spring clips, pump pulls off. Removed two spring clamps and hoses. Reconnected hoses and spring clamps to new pump, put pump back on, put clips back on, dropped washer, put washer back in place. Done. 10 Minutes, max. My twelve year old son could have done it. Part was less than fifty bucks, and service companies want an additional 150 bucks to do the job. Thanks, PartSelect!!

It was a simple & quick repair. pulled the washer forward leaving everything connected except for the electric.. simply unplug it. then tipped the washer backwards. with a droplight & a screwdriver and a pair of pliers replaced the old pump by taking off the metal clamps that were bracing the pump plus the clamps for the hose. also is a good idea to have a pan for the extra water that will drain from the old pump.remove & then put on the new pump & add the clamps you removed. it only took about 15 mins & was alot cheaper than to go buy a new washer. everything works great.

Took two hosses off with pliers and snaped the clips off then pulled pump off of shaft . replaced with new pump. VERY EASY. Thanks Brian

Simple. Removed two hose clamps, pulled off the hoses, removed the clips that held the pump in place and removed the old pump and then simply did the same thing in reverse to put the new pump in. It was easy and the pump was an exact match.

Had a coworker hold washer tillted back, pop both clips that hold pump in place,with pliers remove clamps from hoses.
install hoses on new pump and install pump on motor with the clips.
It took about 12 minutes to do the whole thing.
It was very easy and fast.

First, I laid the washer upon its back and removed the two clamps that held the water pump in place.
with wire pliers.
Next I removed the two inlet water hoses from the pump and sat that pump aside. I then placed the new water pump upon the shaft of the washer and secured the two water inlet hoses back on the new pump wth the clamps. I tightened them with the wire pliers slipping the clamp upon the hoses. Lastly , I snapped the two wire clamps that hold the pump in place back in their groves and immediately placed the washer up right .

Luckily this washer was in the garage and was being made ready to replace an old broken washer. Being able to lay the washer on its side made the job much easier than if it was upright in the laundry closet.

Removal of the old pump was simply a matter of releasing the two clamps holding the input and output hoses and removing the two spring clips holding the pump in place on the motor shaft.

The new pump install required a reversal of the above and took about 3 minutes. It was a very easy and successful repair.

Kayla tilted the washer backwards so I could get access to the pump from below. all I had to remove was two clips then slid the old pump off the shaft and the new one on-clip it in place.Then clamp the hoses on the new ports and we were done in about ten minutes.This made me feel good in three ways... Did A job with my daughter! Save a lot of cash!! and walk away with a great sense of accomplishment !!! Rob@kayla

got under machine and replaced pump

This was very easy. I just pushed the retaining clips off of the pump body (one top side, and one on the bottom) with my fingers. Then I used a pair of channel lock pliers to compress and relocate the spring clamps down the two hoses away from the pump body to remove their clamping action. I removed the hoses, then pulled the pump off of the motor shaft. I lined up the motor shaft with the flat spots in the new pump and installed the new pump in the reverse order. This process took about five minutes and was super easy.