MAH21PSDWW Maytag Washer - Instructions

First thing I did was watch the video the parts company provided. It was concise and kept me from calling the appliance repair man to come right out. It looked easy enough for this 60 plus year old woman to accomplish. The steps they showed were right on. The only part I would emphasize is the rubber grommet can be installed upside down. If it is the air circulator will not fit in. Left me scratching my head for a minute or two. Once that was in the right way it was a done deal. If I had put that in right the first time the replacement would have taken half the time. What a great company!

The machine had the old style boot drain hose with built-in bellows. The constant flexing of this tube caused a small crack in one of the bellows that gradually increased in size over time, causing water to leak into the bottom front part of the machine. Repair accomplished by removing the door (crosspoint screws), the retangular panel above the apron over the door, the apron above the door (5/16 socket), and the front lower panel (crosspoint screws). Pliers used to open the spring hose clamps, old leaky tube removed (re-use the rubber clearance washer that is on the tube). New tube installed easily, then panels reinstalled. 10 minutes total.

Unscrewed old screws, removed old plastic pieces, and replaced

Removed the door removed the hinges removed the screws holding the inner door in place removed all the parts under the inner door put everything back together in the opposit order from taking it out replaced the door wala! finished

I just replaced the pump.

The service representative knew exactly what was needed from the description of the problem that was given to her. The hinges were received within a few days. The door was removed and the hinges were replaced and it does not sag anymore. Thank you for your great service.

Followed instructions that came with replacement part, good as new!

I removed the rear access panel, used a nut driver and pliers to remove the old hose. I tried to connect the new hose with the spring clamp on the pump end of the hose. I gave up on that after a few attepmts because the clamp was very hard to manipulate with standard pliers. I used a standard screw type hose clamp (2") that I had instead. The tub end was easier because a standard hose clamp was used there already. The washer no longer leaks, and I saved a lot of money by doing the job myself!

My husband, a mechanical engineer, kept forgetting to take all the brackets out to hold the screws in place and therefore had to take it apart several times to put the brackets in. Difficult time getting some of the parts out of old door to use in new one without breaking them as most were made of plastic. Washing machine works fine now.

My first time attempted to repair washer and step by step video instruction attached with order confirmation did it for me. Thank you

Replaced the belt and motor isolators. Watching your video made it very easy.

I bought the new Lip Seal Kit thinking that the sound I was hearing had to do with it sticking inside the drum at the end a rotation in either direction. We had replaced the outer drum a few years back when the bearings went. Believe me, you will know when your bearings are going. It sounds like you are in the same room with a jet engine. I knew this sound was not from the bearings. I had the washer apart in about fifteen minutes...and yes, I am a 125 lb. female...so ladies, it is not an impossible task. I have taken that washer apart enough times before that it is no big deal. Just make a mental note as to how it goes back together....if all else fails one can look at diagrams online. My husband just stood there and said "nice job honey". After I got the old seals out and the parts cleaned up, I turned the bearings to make sure they sounded smooth. A-okay. I installed the new seal and smoothed molycote on the spider shaft; replaced the drum, front panels, etc; tightened the pulley with a torque wrench, belt on, etc. and.....turned on the washer. The sound is still there. Sooooo, I am fairly confident that it comes down to the belt and the motor isolators...mostly the isolators...belt is pretty secure. I am changing those tomorrow. Found someone on youtube with the same problem...only far worse...and a response posted said it probably was due to the isolators and belt. Our seal wasn't too fried, but I guess that it isn't a bad thing that I changed it anyway since it has been a few years and they do fail resulting in bearing damage. Better to catch it now. As for whether my machine is worth fixing at its age, I went shopping while this was going on and I don't trust anything out there to not have a multitude of problems. At least with my current model...that still looks like new btw...I don't have a learning curve to deal with on how to take it apart. And a great big shout out to my father who taught me how to dig in my heels and get my hands greasy!! Update: Replacing the motor isolators did the trick. Put on a new belt too as long as I had the back panel off again. Running like a champ!!

Replaced the pump as per video.

The repair was very easy after watching the video that was with the part. I will continue to use this site for other repairs that need to be done.

What transpired was removing the guts from the old inner door and putting them onto the new door which extended the time. Not sure about the tools because my handyman/friend did the installation while I was gone. He was a little frustrated with it. Otherwise, the door fit well. We decided that using hot water was the problem with the water leaking from the door. Using cold and warm water settings seems to make a difference.