MTW6700TQ0 Maytag Washer - Instructions

Removed old tub assembly and installed new tub. Job took a little longer due to first new tub arrived damaged and I had to partially reassemble machine temporarily until second tub arrived.

1. Removed tub to ensure nothing caught to stop rotating. 2. Removed rotor and noted stator had fracture across center from coil to coil. 3. Changed stator, RPS and harness. 4. tested and received F 50 code (no rotation sensed by RPS.5. Changed RPS control board-washer works fine. Hope this repair acts as having a new washer again.

reemplace the lid lock assembly

To start out, I ordered two parts for a washer, a water valve and a recirculation pump. I found out that one of the solenoid switches went bad on the valve body. I tried to find just this switch but found out that you have to buy the whole valve assembly just to get one of the switches. The recirculation pump was making a really bad noise when it would run. The problem with the pump, the impeller that pushes the water out of the pump was in pieces in the pump head housing. I paid to rush the delivery so the washer was not unusable for every long. The parts showed up as planned with one problem. One of the solenoid switches was not attached to the valve body, it was broken off of the valve body. I called the service number that was on the packing slip. The lady I spoke with about the broken part apologized and quickly placed another order with the same part. Down side was she could not get it sent out that day because it was late afternoon on a Friday and the shipping department was closed. So the earliest I would receive the part would be the following Tuesday. She did refund my rush delivery cost, so i paid for just standard delivery. I had the recirculation pump on the Friday I was hoping for but still could not get the washer running until I received the water valve the following Tuesday. I told the lady I understand her hands are tied about shipping the part out that day, Since there was nobody there to ship it. I also understand that sometimes things do get broke in transit. The part was delivered on the following Tuesday as promised. I opened up the package to inspect it. This time the part inside the package was packed a little different and a little more secure. I was glad the service department was easy to deal with, very respectful and willing to correct the problem. All and All The repair went really well, had no problems installing the parts what so ever. (To make things a little easier to remember where they go)Leave the old wire harness intact with the old water valve when you remove it. Once the new water valve is install you can reference how to install the new wire harness from the old water valve. The pump had 3 screws and 2 hose clamps to remove it. It is easier if you can tilt the washer forward (just a little) to change out the pump. You can change out the pump without tilting the washer, just easier if tilted. I would order from partSelect again. I would recommend my friends and family to order from partSelect.

removed glass cover control panel & top of machine to replace hinge spring.

Removed cover and removed rods,replacing them one at a time.

I disassembled the top half of the machine removed the drum and found a bad bearing. The code F51 said i had a bad motor control board. I had a frozen bearing on the main shaft. Freed up bearing, machine now runs but I need to replace the bearing,

Disconnect power and water. Remove the back panel of the washer. The drain pump is on the lower left corner (looking at the washer from the back). Access the electrical connection to the pump motor by lifting the lid where the wire enters the motor. You should be able to do this with your fingers and moderate pressure. Disconnect the electrical plug from the pump motor. Use pliers to remove the two hose clamps, one on the inlet and one on the outlet. Water may leak at this point so have some towels ready. Using a 5/16 wrench/nut driver, remove three hex head self threading bolds that connect the pump and motor to the underside of the tub. The replacement pump and motor go in in reverse order. Note that the replacement pump comes with a moisture shield. The shield installs on top of the new pump between the tub and the pump. It is difficult to see how the shield fits in place when fitting it to the replacement pump. The best way to see how the shield fits in place is to align it on the tub where the defective part was removed. Before testing the repaired washer, consider removing the inner tub and drain compartment cover (located at the bottom back of the inside of the washer). This takes some effort; however, it will save you from repeating this repair. Look for coins or other debris under the inner tub. For instructions on removing the inner tub and drain cover, go to youtube to watch or search for the model number and tub removal on your favorite search engine or youtube. Finally, use the spin and rinse cycle to test the repair. Look to see the pump drains the washer and ensure there are no leaks around any of the hose clamps. Good luck with your do it yourself home repair.