F1201FD (ABWEEUS) LG Washer - Instructions

Watched the easy video instructions on the product page and did the same on our machine - pop off the top, unscrew the plate from the front of the door inset. Its a little challenging to unplug the old lock assembly because it is a tight fit and not enough room for two hands to fit to provide a bit more leverage when pulling the power lines out, but once its out it is easy to install the new one and reattach the strike plate frame and top of the washer. Plugged back in and we were back in business. This $50 part ended up saving us at least $300 in repair fees to get it working again.

Incredibly fast shipping - arrived in less than 2 days - which was really helpful as we were unable to use the washing machine until we were able to get this fixed. Excellent pricing as well. Couldn't be happier I found this site and the product I needed so easily.

Found this part online. I just sets inside, did not click in like the bleach and fabric softener inserts. Think is ok, seems to work

I tipped the right side of the washer up 9.5 inches using two 2x4s and I was able to remove and replace the old hose with the tools described.

Followed instruction from you tube. Removed gasket holder, then gasket by door switch assembly then replaced with new assembly!
I am a 63 woman and found this easy to do, with help from you tube guy.

With my wife's help( 2 shoukder surgeries ), pulled it forward, unplugged power source, turned Both water supplies off.
Removed two phillip screws from each upper ( plastic) holder.
Bumped top from front( works really well if you can use both arms,and with rubber gloves on for traction, or go to harbor freight purchase a glass suction cup) .
I marked ( with a sharpie) the solenoids/hoses,and wires, ( facing front ,right to left,1,2,3.), removed plugs,loosened clamps and pushed them back,gave each hose a twist,and removed them.
Took two screws 5/16 from the back that hold the valve assembly in out.
Removed old valve assembly, put new in place, reverse procedure for assembly. Once all is hooked up,and water dried, I plugged in,turned water on watched for two cycles( you need not stand over it,if it leaks you will know it) to double check, installed top,and we pushed it back in place.
Very simple to do,these washing machines are so easy to work on.
Now we enjoy a dry laundry room,and you can to.
??

When to utube typed in my problem, very easy fix

I followed the video on the PartSelect web site for this repair and it went just fine. I also replaced the drain hose while I had everything apart. Thank you PartSelect, same day shipping. Arrived within 3 day's and your video was spot on.

Followed the video instructions provided.

Viewed two (2) on-line video's for bearing replacement. Produced a 40 item "punch list" as to action to perform following video. Followed sequencing of video's. Noted a 10mm and 17 mm socket needed, used 3/8 drive sockets. Also noted that a "deep Socket" of unspecified size used to aid in removal of nylon pins attaching (3) shock absorbers. Found that 1/2 inch sized (SAE) socket in my 1/2 inch drive socket set fit in the confined space nicely. Did not need the "deep sockets" (3 plus inch overall length) rather a normal sized 1/2 drive socket worked nicely to depress the nylon pin retainers. During reassemble replaced outer tub gasket, checked bolt torque six (6) times over 45 min. to assure complete seating.

I BROUGHT UP THE YOUTUBE REPAIR VIDEO AND FOLLOWED IT STEP BY STEP AND WORKED OUT GREAT THANKS

Pull the washer away from the wall to get behind it. Unplug the electrical power cord from the wall. I removed the top cover by unscrewing the 2 screws on the back of the washer. Slide the cover back about 1-2 inches towards the back of the washer and then lift the cover up and remove. It might be a little tight to slide back, you may need to wiggle the cover side to side or give it a good smack. The water inlet valve is directly at the top inside of the washer. I saw a slow leak dripping from the hot water inlet valve onto the back side of the drum. Turn off the water supply valve at the wall and then unscrew the supply water hose from the water inlet valve at the back of the washer. Disconnect the electrical connector and water hose from the inlet valve inside the washer. From the outside of the washer on the back, remove the screws holding the water valve and lift out the valve. Install in reverse order.

removed two screws from back of front load washer slid the top back two inches and pulled up removing the top.Turned the water off at the shut off . Used the pliers to remove the clamps on the hose to replace. Put the new hose on with new clamps. Un screwed the two screws holding the inlet valve and removed the hose and clamp. Put the new part in and put the hose and clamp back on then put the two screws back that hold the inlet valve.Total time to unpack the parts and install 7 minutes. All I did was google it on youtube and order the parts from this site which only took 2 days and tah dah .

Some screws, some clamps. Easy and straight forward. unplug machine, turn off water, disconnect water hose, unscrew top of machine (2 philips head screws), disconnect clamp from valve (use a towel for remaining water), disconnect wire, unscrew from place holder, remove entire valve, work backwards from there.

Remove old one and replace. Just make sure it is all the way on and secure or you will have a huge mess on your hands.

I watched a video of how to replace the pump and it showed taking the top and front off to get to it. I actually found this could be done by removing the back panel from the washer. There were two hose clamps you have to squeeze and slide up and two wires going to the pump. There are three screws holding the pump that need to be removed from the front of the washer. Once these are removed all you have to do is push a tab down and the motor slide right out. The pump assembly can also be reached from the bottom of the washer.