11049972603 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Eric from Vacaville, CA
- Parts Used:
- WP8182119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Bellow leaking water
Removed the outer spring with pliers. Pushed the bellow into the drum. Loosened the clamp on the bellow with a stub nose screwdriver. Removed the bellow. lined bellow up with soap fiting. Reversed procedure to reinstall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from NEWBERG, OR
- Parts Used:
- WP8182119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Torn bellows was leaking and eating clothes
Followed directions as shown in your repair video, having done this for the first time it took a bit longer than a repairman would have but was able to git-r-done. The most difficult part was fitting the adjustable wire back around the front of the washer, in the video it is made to look really easy however in real life it is a little more difficult and could not be attached so easily and took quite a bit of time to make sure it was attached correctly. thank you for your help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Barrington, RI
- Parts Used:
- 280187
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer wouldn't drain
Easily. 4 Screws. 2 Clamps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from CHERRY VALLEY, IL
- Parts Used:
- WP8182862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Water leaking in to tub when off
Replaced faulty part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from LEXINGTON, SC
- Parts Used:
- 280187
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Error codes SUD and Fo2
Remove three screws on bottom panel lift up and remove panel.The water pump in right in front. One screw holds it in place and the input and output hoses are on the back side.The hose clamps are a little hard to take off I found that before taking the one screw off the pump remove these two lines.Putting the pump back in secure the pump with the one screw. The output line is easy the intake line can be a bit of a more work to get it on because the rubber is so thin.Getting this hose and clamp was tough. Most of all use a wet vac to remove water in washer and vac out the line to drain doing this will be water free during replacing water pump.Run a cycle to make sure the lins do not leak. The other is the people that has posted this replacement are very good
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyime from Wolcott, CT
- Parts Used:
- WPW10250572
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front loader
Lineup slots and snap in place. So easy even a caveman can do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Oceana, WV
- Parts Used:
- WP8182862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Water filling up in drum when not in use
Took top off with nut driver, disconnected 2 wires , removed one screw holding inlet value. Then I reversed the procedure putting new one on. Maybe 20 min. Of course unplug power and turn off water supplies before starting the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from VIRGINIA BCH, VA
- Parts Used:
- WPW10467289
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Replacing the heat sensor following an F-24 Error Notice.
I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from WEST WINDSOR, NJ
- Parts Used:
- WP8182862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Water slowly filling the wash drum and spilling out front of machine
Water was slowly filling the wash tub and spilling out front of machine. Cause was the water inlet valve solenoid was not fully closing.
Turn off water to the machine
Unplug machine
Pull machine away from the wall
Remove the water inlet hoses.
At the back-top of the machine remove the three screws holding the top on.
Lift up top from the rear and remove it.
Disconnect the hose connected to the water inlet valve.
On the outside of the back panel remove the screw holding the water inlet valve.
Remove the water inlet valve.
Reverse the process to install the new valve
NOTE: in my case the hold in the back panel did not line up with the hole in the new water inlet valve. I drilled another hole.
Turn off water to the machine
Unplug machine
Pull machine away from the wall
Remove the water inlet hoses.
At the back-top of the machine remove the three screws holding the top on.
Lift up top from the rear and remove it.
Disconnect the hose connected to the water inlet valve.
On the outside of the back panel remove the screw holding the water inlet valve.
Remove the water inlet valve.
Reverse the process to install the new valve
NOTE: in my case the hold in the back panel did not line up with the hole in the new water inlet valve. I drilled another hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russ from DOVER, NH
- Parts Used:
- WPW10250572
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
unable to get the correct part
the tabs were to big on the replacement and the customer representitive said he was unable to help me.
discouraged
I will never buy parts from this site again
discouraged
I will never buy parts from this site again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from LORAIN, OH
- Parts Used:
- WPW10467168
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Replace tub to pimp hose.
Factory hose clamps were awkward to maneuver. I used automotive radiator hose clamps instead. They worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from Pine Island, TX
- Parts Used:
- WPW10352973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The washer machine didn’t start the cycle. Had a weird sound. Then f 30 was ther error code. With research internet it was easy to know about the motor dispenser problem
I did follow step by step your YouTube video. I’m a woman. There was nothing heavy in the process. You have to be careful that’s it. Thank you for the instructions. I fixed it with the YouTube tutorial you provided. Really nice from you people.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jim from winchester, VA
- Parts Used:
- WP8182119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
front door leaking
2 clamps and its off, problem is if you have average size hands you will struggle in getting the back clamp on and off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from MORGANTOWN, PA
- Parts Used:
- WP8182119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The door bellows had a cut in it
I purchased a new bellows from this site I followed their instructions. Just tricky getting the inner clamp on aligned and tightened.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from REPUBLIC, MO
- Parts Used:
- WP8182119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Ripped bellowspul
Pull spring wire on front. Remove large hose lamp at tub. Reinstall in reverse order.
Was this instruction helpful to you?
Thank you for voting!