11027112601 Kenmore Washer - Instructions

Sir, I have been repairing appliances for 45 years, for myself and friends. I repaired this washer while I talked on the phone with my sister, so with the help of your video I was able to turn a job I thought was going to be extensive to a one handed job, and I did it in 15 minutes.
I am so looking forward to the next repair job, so I can use your web site once more. One word, fantastic.
David Hatcher

Watch the video

Used screwdriver to open top of machine where controls are. disconnected the part, followed the wire along to broken part used screwdriver to remove that part replaced it with new part and fed wires though to where it connects - the whole process took less than 20 minutes

Removed cabinet found tub spring had worn thru rear frame, spring was also almost worn thru. Checked suspension springs very very worn at mounting points.
Ordered needed parts. All in Stock. First bracket came the next day took 5 days to get the rest 1 part at a time.
Forgot to order suspension spring clips, order them next day shipping came the next day .
Just because parts are in stock doesn't mean you will receive in a timely fashion if you need parts better order next day freight.
Videos, parts diagrams and instruction are great, regular freight is not good

I could not make the repair. If you get the pump specified on the shaft that drives the pump, the pump will be broken. I tried to call, nobody answers the phone. I ended up buying a Washing Machine and I'm stuck with a pump I cannot use.

Disconneted hoses,unplugged.removed drain hose.Turned unit on its side.Unsnapped retainers,tryed to to pull off with just my hands,that didn't work.Used a pry bar to pop off.The end of the shaft was rusted out.I took a dremel with wire brush and cleaned up the end.Then the pump njust slid on.I took it off again and applied some anti-sieze on the end of shaft.then put pump back on.Snapped the retainers and put hoses back on.It was easy.When I first looked up washer parts,I found this other site and the price ws doulbe.Then I found you guys ,1/2 the cost and it was here in 2 days.Thank You Parts select.

I removed the cabinet and agitator, layed the machine on it's back, removed the pump, motor and gearcase. I found a way to prop the gearcase up so it rested level, removed the cover, drained the old oil. I removed all internal parts, disassembled them and cleaned them. I reassembled the gearcase using the new uetral drain assembly, and replaced the oil. I made sure the brake assembly was pushed into position and then put the gearcase, motor and pump back in. I sttod the machine up, put the cabinet back on and tested the machine. It still did not spin, so it wasn't the coupler, clutch or nuetral drain assembly.

Yes, I agree that the actual replacement of the pump was an easy task on this whirlpool washing machine, however, unlike other posters, I had no access through the bottom of the machine. My machine has a solid pan on the bottom. It has a large hole in the center - I think to access the transmission, but no access where the pump is.
So, I had to dismantle the entire enclosure, first the back (about 6 screws, a couple of electrical connections, etc.), then remove the rest of the enclosure to reveal the guts of the machine. I also had to disconnect a small vacuum tube attached to the tub, and remove the control console on top along with the back. It was pretty straight forward, took about two hours to dismantle. Then, the actual removal of the pump was as easy as others have described here - two spring clips and a hose clamp and I had it in my hand. I ordered the new part, which came very quickly - 2 days I think. Then I took another two hours to re-assemble the machine. It works - yeah!
Symptoms - water leak on the floor, it was actually intermittent for a time, so I procrastinated. Then when I actually did the work, I could see the rust trail and follow it to the leaky pump. The pump was actually leaking through the center, where the drive shaft from the motor goes. There is probably a seal between the impeller and the central drive slot that gives out after a while.
New pump in - machine back together - no leaks.

removed water lines from back of washer. tilted washer to get access to the pump/ removed 2 hoses at pump and removed to snap clips attaching the pump. easiest repair i ever did. washer works fine now.

Tipped the washer onto it's side, used pliers to loosen clamps on old hose. Removed outer drain hose from white plastic hose adapter on back of washer. Removed white hose adapter (snaps out of place) and old hose. Fed new hose through opening for white adapter, then snapped new adapter into place on back of machine. Put the new hose in place and replaced clamps. Sat washer back upright. No more leaking! It was easy and didn't take more than 15-20 minutes.

Repair went well and relatively easy, but did not fix the problem.
Suspect timer switch was the culprit. Nothing was clogged or plugged
up. Water pump and impeller were free and clear with no damage
or leaks.

I am an old woman who is disabled and without any tools or knowledge, but sheer stubbornness and will power, I waited for my tools and other parts to come in, in the mean time I fixed my young neighbors whirlpool washer, well We took top off the nut I had already pre assembled her cam so set it in place of old one put bolt back in place and the top of agitator she says works perfectly now, my parts came in I had nothing to remove as my handicap daughter had already thrown away all the loose parts, I threw away old top agitator, assembled cam and put in place still did not feel tight enough so added seal from other nut!! it worked tight enough, put the inner part back in with new part and soap put the top back on and now works good as new, was disappointed could not put bottom agitator in place, just not strong enough lol well this was my story

We unscrewed the two screws at the back of the control panel. Holding the control panel on both ends
we pulled it toward the front of the machine, slightly and gently lifting it at the same time, removing it from the metal surround. Holding the control panel up off of the surround we rocked the surround forward and lifted it off the washing machine frame.
We could see where the leak was coming from. We took the hose clamps from the two ports, then
using a pair of pliers pulled the two clips that are holding the pump onto the shaft protruding from the
electric motor. We matched up the part on the web sight. Ordered the part then when it came in we just reversed the order putting the machine back together. The hardest and most time consuming
thing about this repair was the clean up of the washing machine. (Dirt and soap residue does
build up on the inside of the wash tubs.)

Being female & never working on appliances, it was a challenge for me. I took the spinning unit apart: 1) Outer cap 2) Inner cap 3) Screw, nut & bolt popped out. Rusty & wouldn't lock into place anymore. Ordered nut & washer at about $10 + shipping. Total $17 from MayTag Rec'd right at 7 days via USPS. Used nutdriver/wrench to screw in new bolt w/washer. Wah la! That did it! Washer working great now! Now that I'm a "diy" handy person, I'm ready for my next challenge. Hopefully, none!

Replacing the clutch was easy but unfortunately did not fix the washing machine. I couldn't get the agitator loose at first, but it came loose when I unbolted the motor and transmission assembly. After replacing the clutch and reassembling the motor, I tilted the washer back up and found that the basket in the center under the agitator was cracked all the way around and that was why it wasn't spinning. It was also why the clutch was burning--trying to spin a basket that wasn't centered in the drum anymore. This washer is over 25 years old, so I decided not to replace the basket, since a replacement is about $400. A good attempt at an inexpensive repair, but unsuccessful.