1108293130 Kenmore Washer - Instructions

Went on line and ordered the piece I need. I got my socket set out, held the center piece in place then with the socket unscrewed the bolt. Popped the plastic washer off put the agitator clips in, put the plastic washer on and bolted it back together and was done. Easy as 1, 2, and 3.

Went on line and did a search for Kenmore Washer Select Knobs through the Part Select website. The associated photo made it easy to match to my broken part. Ordered it and received it in 3 DAYS!!! Unwrapped the new part and screwed it on (the knob is threaded)- took longer to unwrap the part than to install it!!! I Love PartSelect.com!!! This was the 2nd time I have used them and will continue to rely on them whenever possible for my appliance repair needs!!!

I pulled the hose off and notice their was a part # and I went online and type the part # and showed the part and cost. I order it and receive it within 3days. when the part arrive I replace the hose in minutes. If I can do so can you its that easy.

Removed the old hoses and screwed on the new hoses.

We watched a video on YouTube; it was very easy . We had to use the mounting bracket.

This website was such a big help. I just followed the directions of the other prople who answered. I was able to do this even though I am not that mechanically inclined. The toughest part was removing the two metal clips that hold the back to the top. I needed a screwdriver to lift these out, but after this the repair was a simple matter of following the old switch line along the inside top of the washer body, removing the ground wire (a bit tricky because you have to lean the unit foward while trying to remove a screw that hangs down at the same time). and screwing in the new unit. Thanks to everyone who posted comments before. You were real life savers (and saved me hundreds of dollars in repair costs or replacement fees!!!!!!!). Thanks again!

Removed screws from top control panel. Tilted panel back. Unsnapped two retaining clips and pulled entire washer cover forward. Turned off water and uplugged washer. Disconnected hot and cold water supply. Disconnected supply tube from water inlet valve. Disconnected electrical hook-ups to water inlet valve. Removed water inletvalve. Installed new valve being careful to use new mounting plate supplied and making sure screw holes line up correctly. Re-connected all disconnects and it works like new!

Disassembled lower part found nothing wrong.
Started disassembly from the top. Immediately ran into trouble not knowing exactly how the tub was anchored to the drive. Once I got down to the tube and drive block there was nothing I could do to go further. I guessed it was a press fit onto the drive, but there were many instructions and I couldn't be sure. Parts Select expanded drawing was the most useful tool; it was correct omitting a few details. Anyhow, cleaning out my garage I found one of my old gear pullers that I could ring to complete the disassembly. All the sudden I was in business, pulling the washer drum off the drive block and shaft, getting down to the leaky lower seal. A that point it was just a matter of cleaning everything up and buying all the rusted out parts to reassemble. I spent $150-200 on parts, but its completely rebuilt now and runs like a charm. Probably have around 20-50 hours all told, into the repair. Most of this was reading instructions, watching videos, and trying to figure out the rest (3). Doing the actual work spread over time until my wife and sons threatened to throw the thing out. Never. Once I decide I'm gonna do something, I do it. LOL!

I followed the provided video for changing the centerpost gasket.

I successfully completed the repair. I will say that I had challenges at almost every step. Getting the inner basket off the centerpost was difficult, as was rocking the outer tub upward from the base.

If a man is somewhat handy, this is a doable repair. Be patient and take your time. The video is very helpful and I don't think I could've done the repair without it. It's a pleasure to watch an expert like Steve.

It's gratifying to successfully repair a major appliance such as a washing machine and I look forward to many more years of reliable service from this well-built appliance.

I needed the washer ASAP. I paid extra for the expedited shipping. The parts arrived as promised. I watched the on-line video. I read and followed the included instructions. Removed cap and nut. Pulled out part with "dogs", swapped new dogs and assembly. Re-installed components, I was wary from information gleaned from the video, which warned of proper orientation of "dogs", as they can be inserted backwards. Tightened bolt and re-installed cap. Presto! Repaired washing machine worked as good as new. My coffee didn't even get cold.

took replacement knob & threaded it back onto post. Done in literally seconds ! ! ! Took longer to open the package than to install new knob.!

unpluged the washer. removed the two screws on console. unpluged the lid switch connector and seperated it from the cabinet.removed the body clips. removed the washer cabinet. removed the two screws holding the lid switch. removed the two cable or wire clips.
checked new part against the old. put the two screws mounting the lid switch back in. put the two cable clamps back securing the lid switch wires. put the cabinet on.reconnected the lid swich wire connector to the cabinet.pluged in the lid swich to connector.put the body clamps back in place.put the two screws holding the console back in. plug washer back in to main power. stared the washer and ran it through a cycle testing the lid switch.
worked great.
Thanks

I removed the cover for the softener dispenser on the top of the agitator. Then reached in and removed the cover of the nut and washer which was very sticky and sealed with an o-ring. This took a bit of pressure. Then used a socket wrench with an extension to loosen the bolt and took the whole agitator out of the machine. Then I set the agitator on the floor and with a fine 12 inch long screw driver released the catches while turning and pulling the agitatior with my other hand and holding the lower agitatior on the floor with my feet. I then turned the upper part over and removed the cogs and holding mechanism.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.

undo one bolt and change agitator kit

Installed part, now it works great!