55325119 General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Beth from Edmonds, WA
- Parts Used:
- WH1X2754
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The timer knob broke on the washer
I pulled off the broken part and popped on the new knob. I probably spent less than 5 minutes fixing the problem. Super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karla from Boothbay Harbor, ME
- Parts Used:
- WH1X2117
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Handle plate would'nt turn
Pulled off the handle with the kneedle nose pliers replaced the plastic piece in that, then pulled off the plate that turns the machine on and just snapped the new one on. Only took seconds and saved alot of money. Considering just to have a repair man come to see what was wrong would have cost me $88.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from PRESCOTT, AZ
- Parts Used:
- WH1X2754
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Cycle knob shaft was broken at the clip
Removed old clip and remnants of old shaft. The key is.to keep the clip in the new knob and push it over the cycle shaft.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rob from SILVERTON, OR
- Parts Used:
- WH1X2754
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broke theteeth off the stem of the dial so it wouldn't allow selection of start/ load size etc.
Part came in after a couple days and it was a simple push on to the stem and it was done! Not the most difficult fix. Getting the right part first time was the best part!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from TUSCUMBIA, AL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken starter knob
Just pushed the knob on by hand and it was ready to start! It was great not having the extra expense of a house call! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessica from Spanaway, WA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Start knob on dryer broken
There really is not much to explain, the new knob was so simple to replace that my six year old could have done it. No tools were required and it took less than a minute to replace the new knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy W from Albany, OR
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
On knob was broken
Removed knob and installed the replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wagdy from Watertown, MA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The two dial buttons were broken on a white appliance. The dials sent were bone white.
Pull out old, insert new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Levittown, PA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing knob
the part fixed all the problems in a cinch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from Dunmore, PA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer wouldnt start
just replaced the old knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- matthew from medfield, MA
- Parts Used:
- WH1X2754
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
broken timer knob on ge profile washer
could not have been easier. It took a pair of pliers and a few minutes time to remove the remaining portion of the old knob from the spindle. Then simply push the new knob into place.worked perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Portland, OR
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bdryer broken knob
I just put the new knob where the old one was and presto it was done. The whole process was much easier than I expected.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- faye from reading, PA
- Parts Used:
- WH1X2754
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Waher Knob Broke When Turning On.
First I had to remove old knob part from washer. Then I put the new one on. It was that easy,anyone could do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlos from Los Angeles, CA
- Parts Used:
- WH1X2754
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Bakc Part With The Teeth Broke Off With The Clip.
Just pushed on the knob into place and it clipped on. No problems or issues. Thanks so much for posting pictures of the parts in all angles I was able to identify it since I didnt have the part number. Ordering and shipping was quick and easy. Thanks carlos a.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Piscataway, NJ
- Parts Used:
- WH1X2754
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old knob broke
Push new knob on
Was this instruction helpful to you?
Thank you for voting!