GTW485ASJ4WS General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- david from OAKLAND, OR
- Parts Used:
- WH43X31240, WH43X24454
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Top of auger was broken
Instructions were fairly good, line up holes and push a phillips head screwdriver thru auger then twist it off. Problem is you can only use a short screwdriver due to space limitations, and it is or at least for me was impossible to twist the auger off as directed, but after I lost my temper and gave the screwdriver a good thump (auger was already broke, what's the harm) with my left hand the auger came right off, putting the new one on is very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heather from CHARLESTON, IL
- Parts Used:
- WH08X37938
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Don’t do this, but we prop the washer lid open so it doesn’t get musty between use; we put a sock or something in there to prevent the striker fro closing. When a family member hops up on the washer to get to the highest shelf in the laundry closet it snaps! And the. The washer won’t function.
REALLY easy-
Just unscrewed the two screws with a Phillips, slid the old one out, the new one set in perfectly, and used the same screws to hold it in place. 2 minute task total.
Just unscrewed the two screws with a Phillips, slid the old one out, the new one set in perfectly, and used the same screws to hold it in place. 2 minute task total.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Cypress, TX
- Parts Used:
- WH23X28418
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench (Adjustable)
Washer would not drain after a load of wash
Being a woman I had to figure out tipping it in its front. I put it on a dollie and drop it down real easy.
Removed all water lines after water was shut off.
Removed bolts. Removed bolts on plate to the right to unplug old pump.
Plugged in new one and replaced all bolts, hoses and tipped her back up. Works like a charm and I saved $408 by doing it myself!!!!!
Removed all water lines after water was shut off.
Removed bolts. Removed bolts on plate to the right to unplug old pump.
Plugged in new one and replaced all bolts, hoses and tipped her back up. Works like a charm and I saved $408 by doing it myself!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from FOLEY, MN
- Parts Used:
- WH23X28418
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Wash machine would not drain/pump water out of machine.
1 Disconnect power 2) Cut water supply to washer 3) Disconnect water supply hoses from supply.
***if pump broke with water in tub, remove water from tub. 4) tip machine onto it's front side 5) remove hose clamp of exhaust hose & then remove exhaust hose from pump 6) Remove pump with socket/ratchet 7) disconnect pump electrical plug 8) tell old pump to take a hike & throw in garbage 9)Iinstall new pump 10) Do steps 7—1 in reverse order to put back into business.******Be prepared to do it again in 6 months; I havnt had good luck!
***if pump broke with water in tub, remove water from tub. 4) tip machine onto it's front side 5) remove hose clamp of exhaust hose & then remove exhaust hose from pump 6) Remove pump with socket/ratchet 7) disconnect pump electrical plug 8) tell old pump to take a hike & throw in garbage 9)Iinstall new pump 10) Do steps 7—1 in reverse order to put back into business.******Be prepared to do it again in 6 months; I havnt had good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lindy from LILLINGTON, NC
- Parts Used:
- WH23X28418
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
The washer did not drain. It also did not click or sound like the drain cycle was being engaged.
Emptied the washer, took the back cover off, tipped it foward, unplugge the old pump, remove two mount bolts. The replaced the new pump. The new pump resolved the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vikki from CORDOVA, TN
- Parts Used:
- WH01X24180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench set
water pump replacement
went online to replace water pump on washer site and followed directions. Very easy installment.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIKE from POMONA, CA
- Parts Used:
- WH08X37938
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Lid wouldn’t lock keeping machine from working
Unplugged the machine, pulled it away from the wall, didn’t have to disconnect water lines, set the parts out on the counter as I went over the instructions a couple of times, followed the directions, plugged it back in, worked perfectly again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kirby from IROQUOIS, SD
- Parts Used:
- WH08X37938
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
The washer would fill with water then stop.
Open up the top of the washer per instructions. Remove the old switch and wiring harness. Install the new wiring harness and switch. The instructions that were provided are very descriptive so the installation went flawlessly. The switch has been redesigned and looks to be more robust than the original. The washer now works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from BAREFOOT BAY, FL
- Parts Used:
- WH13X26535
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Water would drip onto the tub when not running
Take cover off use socket driver to remove two hex head machine screws. There was a foam piece attached to the old part that i pealed off and attached to the new part. It’s there to prevent rattles. There is a tube that pulls out of the old part and a grommet inside that must be removed and placed in the new part. Connect the two electrical plugs and install the new part just like the old part came out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricky from KRUM, TX
- Parts Used:
- WH12X27614
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Would not spin
Took 4 screws out of back of control panel. Tested old capacitor. Installed new one. Put back on tested spin cycle everything is doing great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Frederick, MD
- Parts Used:
- WH04X29308
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Selector switches were non responsive in operation and diagnostics.
I downloaded the repair manual on line and followed the instructions for running the diagnostics. This showed that the selector switches were faulty. I then replaced the selector switches following the instructions in the repair manual. Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rock from HOUSTON, TX
- Parts Used:
- WH13X26535
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench set
leaking water inlet valve on washer
I watched a youtube video to see how others performed the repair. My washer was a little different than in the videos but the inlet valve was very easy to access once I pulled the washer out of it's "nook". I took off the back panel of the control "box" (4 screws). Then accessed the valve which was held in place with two screws. The screws were buried behind a few wires so they were a little difficult to access but not impossible. I did need to use my 1/4" box end wrench as my son had borrowed my socket set.
The people at PartsSelect were helpful in selecting the right part and the repair is working fine. My wife is happy.
The people at PartsSelect were helpful in selecting the right part and the repair is working fine. My wife is happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- terry from MILLINGTON, TN
- Parts Used:
- WH03X30517
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
washed well but would not shift out of spin cycle
easiest repair I have ever made. No problems and was surprised as to how fast and easy it was to repair. I did not need two of steps the instructions stated I had to do. best purchase I have ever made.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from GAINESVILLE, FL
- Parts Used:
- WH08X37938
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The machine would not start all the time.
Watched You Tube and had at it. In the end it was fairly simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from GROVE CITY, OH
- Parts Used:
- WH13X26535
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
When not in use, water was dripping into the washer
We are on a fixed income so my wife and I did the repair ourselves. Thanks very much to the instructions George from Clarksville, Tn. provided on your website. She read the instructions and I followed them. the repair went excellent, THANK YOU GEORGE. All is well
Was this instruction helpful to you?
Thank you for voting!