GTWN5650F2WS General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from CONYERS, GA
- Parts Used:
- WH01X10302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Broken Belt
The video on your site on the page for this belt was perfect. Really just using a tie wrap to hold the belt as you spin it to put in place was a very helpful idea. It was easy and less expensive than a new washer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from BRIMFIELD, MA
- Parts Used:
- WH43X10032
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Not agitating, free spinning agitator
Popped cap off of agitator and used 12inch extension with 3/8 socket to remove bolt. Pulled off agitator and turned upside down. I then used 4 flathead screwdrivers to depress tabs on old coupling and flipped agitator back over and used a long screwdriver to push old coupling out. Flawless! Wiped everything down and pushed new agitator coupling right in place! Perfect! Put everything back together and washer is back in business!! Thank you PARTSELECT!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Priscilla from Beverly, MA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
broken dampening strap
Watched the video, read installation instructions.
Replaced four broken dampening straps, washer is quiet and all is good.
Replaced four broken dampening straps, washer is quiet and all is good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mabry from CLINTON, MS
- Parts Used:
- WH43X10034
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Agitator was broken
First tried pulling the old agitator out by hand but couldn't get my fingers under it to pull upward. Tried several times but no success. Finally put two metal rods about 8 inches long in the holes in the bottom of the agitator and used them to lift upward, it came up immediately. I then pushed the new agitator down into the slot and it was finished. There is always a way when you think about it.you are a winner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arlis from Moore, SC
- Parts Used:
- WH01X39337
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Tube Shaking Like Out Of Balance. Water Not Draining Completely And Created An Unpleasant Odor
Main thing is watch the video. It may vary a little according to the age of your appliance, as it did with me but common sense guides. The difference was minor on my part. Two hex head screws to remove per strap and they had to make them 1 size different. Go figure. Have your change handy. A ratchet nut driver will save you some time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cynthia from winter park, FL
- Parts Used:
- WH41X10096, WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
washer leaked water
after reading repair stories, decided I should take front panel off and see where leak was coming from. taking the panel off was real pain but well worth as inside was dry! so I looked again and discovered a pin hole in drain hose that only leaked when tub was full. while I had panel off I noticed tub dampening straps were broken so went ahead and ordered those parts too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Rosemead, CA
- Parts Used:
- WH23X10043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
wasn't draining the complete water
really easy repair, just open the front cover panel & removed the Drain Pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from OVERLAND PARK, KS
- Parts Used:
- WH12X10334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Water temp will fill hot only with lid open. Close the lid and it is cold water only.
The video I watched said to remove front panel, control panel, and top panel. After I removed the front panel, I was able to remove the lid switch and splice the wires together and reinsert in the mounting without removing the other panels. Secured with wire tie and put front panel back in place. This did not, however fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helmut J from New Berlin, WI
- Parts Used:
- WH12X10276
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
water, spin cycle not functioning
After receiving the wrong part 2x instead of magnet assy I received a metal clip ring. ordererd magnet assy from another source. iNSTALLATION IS VERY SIMPLE. REMOVE 2 SCEWS IN THE LID WHICH HOLD THE MAGNET IN PLACE AND REPLACE THE MAGNET WITH NEW ONE. TEST TO MAKE SURE ALL OPERATIONS ARE NORMAL.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joel from mt vernon, IL
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
two tub dampening straps snapped
I just watchied the clip on the website during the day about how to fix it, went home that night and fixed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- larry from Steamboat Springs, CO
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
broken tub strap
follow youtube vid. simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrance from Eldom, MO
- Parts Used:
- WH01X39337
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
A banging noise while the machine was washing.
The repair was done like the video suggested to do and in the order. And it worked well.In the step by step procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from Bynum, TX
- Parts Used:
- WH41X22935
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
had a pin hole in the drain pipe
order the part and replaced it and it works just great! May I add never before have I had such an amazing experience in dealing with your company, your company shows pictures and I ordered the part in the late afternoon and I had it the next day, the diagram you show on your site was so helpful, you told us that the part now is replaced with a different #. Once again KUDOS!! to your co.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pansy from STARKVILLE, MS
- Parts Used:
- WH12X10334
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Washer wouldn't spin out
Someone did it for me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from ROCHESTER, NY
- Parts Used:
- WH01X10302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Had to replace drive belt on washer
I removed the front cover on washer I tied wrapped one side of the belt to to the back pulley and placed the belt on the the motor pulley then placed the belt installer on pulley below belt with gloves on I started rotating the pulley in the back and when it started getting s little tight I moved pulley back and forth then started turning in clockwise direction again and belt went right on.i cut the tie wrap after making sure belt was secured and evenly on then turned pulley to make sure belt was secured removed belt installer and replaced front cover.i am a 57 yr old woman and did this job by myself.so easy when you have the belt installer also.
Was this instruction helpful to you?
Thank you for voting!